AMX CCD-15APS-1

AMX CCD-15APS-1 mode d'emploi

(1)
  • RF Plug-In Modules
    Dimming Module : CCD-3PD-1
    Appliance Module: CCD-15APS-1
    120 V
    50 / 60 Hz
    Typical Power Consumption*: 0.3 W
    Installation Instructions
    Please Read Before Installing
    Installation
    Dimming Module Operation
    Troubleshooting Guide
    Lutron Elec tron ics Co., Inc.
    7200 Suter Road
    Coopersburg, PA 18036-1299
    Print ed in the U.S.A. 1/11 P/N 044-275 Rev. A
    Load Specifications:
    Control Load Type Min. Load Max. Load
    3PD-1
    Incandescent, Halogen 10 W 300 W
    MLV 10 W / VA 200 W / 300 VA
    CFL, Fluorescent, ELV
    (Switching Mode Only)
    10 W 300 W
    15APS-1 General purpose None
    1/2 HP
    ††
    15 A
    Technical Assistance:
    U.S.A. / Canada: 1.800.523.9466 Fax +1.610.282.6311
    Mexico: +1.888.235.2910
    Other Countries: +1.610.282.3800
    24 hours a day, 7 days a week.
    Important Notes
    WARNING - Entrapment Hazard - To avoid the risk of entrapment,
    serious injury, or death, these controls must not be used to control
    equipment which is not visible from every control location or which
    could create hazardous situations such as entrapment if operated accidentally.
    Examples of such equipment which must not be operated by these controls
    include (but are not limited to) motorized gates, garage doors, industrial doors,
    microwave ovens, heating pads, etc. It is the installer’s responsibility to ensure
    that the equipment being controlled is visible from every control location and that
    only suitable equipment is connected to these controls. Failure to do so could
    result in serious injury or death.
    NOTICE: To avoid overheating and possible damage to other equipment, do
    not use -3PD-1 to control motor-operated or transformer-supplied appliances or
    other non-lighting loads. Always use a light bulb that remains within the wattage
    rating of the light fixture.
    Codes: Install in accordance with all local and national electrical codes.
    Environment: Ambient operating temperature: 32 °F to 104 °F (0 °C to 40 °C),
    0% to 90% humidity, non-condensing. Indoor use only.
    Cordset: The cordset has a plug on a 24 in (610 mm) cord and a receptacle on
    a 6 in (152 mm) cord.
    Cleaning: To clean, wipe with a clean damp cloth. DO NOT use any chemical
    cleaning solutions.
    Load Type: The -3PD-1 is designed to dim one incandescent, magnetic low-
    voltage, or tungsten halogen table or floor lamp. The -3PD-1 can be configured to
    switch a compact fluorescent, fluorescent, or electronic low-voltage load. Use with
    lighting loads only. Do not use to control a lamp that contains an integral dimmer
    or a touch lamp. For a lamp with an integral 3-way switch, the switch should be set
    to full on position. The -3PD-1 may not work with dioded light bulbs. Always use
    a load that complies with the Load Specifications table above. Always use a light
    bulb that remains within the wattage rating of the light fixture.
    The -15APS-1 is designed to switch general purpose loads (lighting, non-lighting,
    motor-operated, or transformer supplied appliances). Total connected load can
    not exceed 1/2 HP, or 15 A.
    Low-voltage Applications: The -3PD-1 can be used with magnetic (core
    and coil) low-voltage transformers in both dimming and switching modes.
    Use with electronic (solid-state) low-voltage transformers in switching mode
    only. Operation of a low-voltage circuit with light bulbs inoperative or removed
    may result in transformer overheating and premature failure. Lutron strongly
    recommends the following:
    a. Do not operate low-voltage circuits without operative light bulbs in place.
    b. Replace burned-out light bulbs as soon as possible.
    c. Use transformers that incorporate thermal protection or fused transformer
    primary windings to prevent transformer failure due to overcurrent.
    RF Device Placement: RF Plug-In Modules must be located within 30 ft (9 m)
    of an RF signal repeater. For systems with an RF signal repeater, RF Plug-In
    Modules cannot be controlled by the system until they are programmed in a
    system according to the system Setup Guide.
    English
    Lutron and the sunburst logo are registered trademarks and Clear Connect is a trademark of Lutron Electronics Co., Inc.
    ©2011 Lutron Electronics Co., Inc.
    120 V 50 / 60 Hz
    ®
    COOPERSBURG, PA 18036 USA
    I
    H
    300 VA /
    200 W
    300 W
    1. Place the Plug-In Module in a convenient and accessible
    location.
    2. Turn the load ON and unplug the cord from the wall outlet.
    3. Plug the load cord into a Plug-In Module receptacle.
    4. Insert the plug of the Plug-In Module into the wall outlet
    5. Turn the Plug-In Module ON.
    6. Verify operation. See Dimming Module Operation and
    Appliance Module Operation.
    WARNING - Shock Hazard - To avoid the risk of
    electrical shock, unplug the Plug-In Module when
    changing light bulbs. Changing light bulbs with the
    power on could result in personal injury or death.
    WARNING - Shock Hazard - To avoid the risk of
    electrical shock, do not open, cut cord, or rewire the
    Plug-In Module. Modification of the module can result
    in personal injury or death.
    NOTE: -3PD-1 contains a
    POLARIZED cord set. It
    has a polarized plug (one blade is wider than the other) and
    receptacle (one slot is wider than the other).
    The polarized plug is not intended to be mated with non-
    polarized outlets (having both slots the same size).
    The polarized receptacle is intended to mate with a polarized
    plug in only one way (the wider slot with the wider blade).
    Status LEDs (1-7)
    Indicate light level; glow softly as night light when load
    is OFF
    Toggle Button
    Press to toggle ON / OFF; double-tap for full ON; press
    and hold while ON for delayed long fade to OFF.
    Raise Button
    Press to brighten
    * Typical Power Consumption test conditions: load is off.
    Lower Button
    Press to dim
    Use these instructions to install the model numbers listed above. For system Setup
    Guide and tools visit www.lutron.com
    CCD-3PD-1 (1 receptacle) CCD-15APS-1 (1 receptacle)
    Plug-In Module
    Plug-In Module Receptacle
    Plug-In Module
    Plug
    120 V 50 / 60 Hz
    1/2 HP 15 A
    ®
    COOPERSBURG, PA 18036 USA
    Status LED
    Indicates load status; glows softly as night light when
    load is OFF
    Toggle Button
    Press to toggle ON / OFF.
    Appliance Module Operation
    I
    H
    1. Tap the toggle button to turn off the load.
    2.
    Press and hold the toggle and lower buttons for 3 seconds until
    LED 1 flashes to enter Advanced Programming Mode (APM).
    3. Tap the raise button until LED 7 flashes.
    4.
    Press and hold the raise button until LEDs 1 and 3 flash.
    5. Tap the toggle button once, wait 2 seconds, then tap the
    toggle button again. Notice the LEDs that flash: LEDs 1 and 7
    (Dimmer mode - Default), LEDs 2 and 7 (Switch mode).
    6. Tap the raise button once. LEDs 2 and 7 will flash and the
    module will be in switch mode.
    7. Press and hold the toggle button for 6 seconds to save this
    setting and exit APM.
    NOTE: To change module back to dimmer mode, repeat steps
    1-7 and select LEDs 1 and 7 in Step 6.
    NOTE: If desired, the Dimming Module can be configured to
    function as a switch for lighting loads only.
    NOTE: During programming, the Plug-In Modules turn loads
    ON/OFF very quickly. Unplug sensitive loads before proceeding.
    Advanced Programming (Dimming Module to
    switch mode)
    1
    3
    7
    2
    Symptom Probable Cause and Action
    Load does
    not turn ON,
    but LEDs on
    the Plug-In
    Module are ON
    Load is turned OFF
    Turn the power switch on the load to the full
    ON position.
    Light bulbs are burned out or not installed
    Replace or install light bulbs.
    Dioded light bulbs
    Replace with non-dioded light bulbs.
    Load does not
    turn ON, and
    LEDs on the
    Plug-In Module
    are OFF
    Circuit breaker is OFF or tripped
    Turn circuit breaker ON.
    Cord is not plugged in
    Plug cord into wall outlet as shown in Installation.
    Load turns
    ON and OFF
    continuously
    Load is less than minimum load requirement
    Make sure the connected load meets the
    appropriate minimum load requirement. See
    Load Specifications.
    Dimming
    Module does
    not dim
    properly
    Lamp has an integral dimmer
    Use lamp without an integral dimmer.
    3-way switch on lamp is not set to full ON
    Turn 3-way switch on lamp to full ON
    Plug-In Module
    is warm
    Solid-state control dissipation
    Plug-In Modules dissipate a small percentage
    of the total connected load. It is normal for
    the Plug-In Module to feel warm to the touch
    during operation.
    Appliance
    Module
    automatically
    turns off
    Over temperature condition
    Move Appliance Module to a cooler location
    and / or reduce the load, then unplug and plug
    the Appliance Module into the wall outlet.
    Plug-In Module
    doesn’t
    respond to
    a keypad,
    wireless
    controller, or
    sensor
    Improper programming
    Program according to the system Setup Guide.
    Out of RF range
    Reposition to be within 30 ft (9 m) of an RF
    signal repeater.
    Already at current level
    The Plug-In Module has already responded to a
    command, or is already at the requested setting.
    Wireless controller or sensor batteries low or
    installed incorrectly
    Replace or install batteries properly.
    RF inteference
    Do not run Plug-In Module cords with other
    power cords or communication wires (i.e.
    networking, audio, or video signals).
    Note: Refer to the system Setup Guide for additional troubleshooting
    suggestions.
    Returning a Plug-In Module to Factory Settings
    Note: Returning a Plug-In Module to its factory settings will remove it
    from the system and erase all programming.
    Note: Unplug all switched loads from the Plug-In Module prior to
    returning to factory settings.
    Step 1 : Triple tap the toggle button on the Plug-In Module. DO NOT
    release after the third tap.
    Step 2 : Keep the toggle button pressed on the third tap (for
    approximately 3 seconds) until the LED(s) on the
    Plug-In Module scroll up and down or flash quickly.
    Step 3 : Release the toggle button and immediately triple tap it again.
    The LED(s) on the Plug-In Module will scroll up and down or
    flash slowly.
    The Plug-In Module has now been returned to factory settings and needs
    to be reprogrammed into a system.
    Warranty:
    For warranty information, please see the enclosed Warranty, or visit
    www.lutron.com/resiinfo
    NOTE: Advanced Programming of a Plug-In Module requires
    access to the module. Do this BEFORE installing if the module
    will be hard to reach once installed. No load is required. You
    may use any wall outlet within RF range.
    Some low wattage loads may try to start when the Appliance Module is OFF due to 0.5 mA leakage
    current through the module, similar to a night lighted toggle switch. Consult the load manufacturer for
    compatibility.
    ††
    Peak horsepower is not reflective of the UL® appliance horsepower rating. Consult appliance
    manufacturer for UL horsepower rating.
    Load Cord
    Wall Outlet
AMX CCD-15APS-1

Besoin d’aide?

Nombre de questions : 0

Vous avez une question sur le CCD-15APS-1 de la marque AMX ou avez-vous besoin d’aide? Posez votre question ici. Fournissez une description claire et complète du problème et de votre question. Plus votre problème et votre question sont détaillés, plus il sera facile pour les autres propriétaires du CCD-15APS-1 de la marque AMX de répondre correctement à votre question.

Consultez gratuitement le manuel de la marque AMX CCD-15APS-1 ici. Ce manuel appartient à la catégorie Gradateurs et a été évalué par 1 personnes avec une moyenne de 6.7. Ce manuel est disponible dans les langues suivantes: Français, Anglais, Espagnol, Portugais. Vous avez une question sur le CCD-15APS-1 de la marque AMX ou avez-vous besoin d’aide? Posez votre question ici

Spécifications du CCD-15APS-1 de la marque AMX

Généralités
Marque AMX
Modèle CCD-15APS-1
Produit Gradateur
Langue Français, Anglais, Espagnol, Portugais
Type de fichier PDF
représentation / réalisation
Type Variateur et commutateur
Design
Rangement Externe
Type de commande Indisponible
Couleur du produit Blanc
Certification cUL, UL, FCC, IC, SCT, NOM (-3PD only; -15APS pending)
Puissance
Tension d'entrée AC 120

ModesdEmploi.fr

Vous cherchez un manuel ? ModesdEmploi.fr vous permet de trouver le manuel que vous recherchez en un rien de temps. Notre base de données contient plus d'un million de manuels en PDF pour plus de 10 000 marques. Chaque jour, nous ajoutons les derniers manuels afin que vous trouviez toujours le produit que vous recherchez. C'est très simple : entrez le nom de la marque et le type de produit dans la barre de recherche pour consulter gratuitement et immédiatement le manuel de votre choix en ligne.

ModesdEmploi.fr

© Copyright 2020 ModesdEmploi.fr. Tous droits réservés.

Nous utilisons des cookies pour vous garantir la meilleure expérience sur notre site. Si vous continuez à utiliser ce dernier, nous considérerons que vous acceptez l'utilisation des cookies.

En savoir plus