Casio Edifice EQW-A1000DB-1AER mode d'emploi

Casio Edifice EQW-A1000DB-1AER
9.1 · 8
PDF mode d'emploi
 · 12 pages
mode d'emploiCasio Edifice EQW-A1000DB-1AER

Operation Guide 5142

While crown button mode switching is disabled, pressing the crown button will x
cause the
Second Hand to move to the 3 o’clock position. The
Second Hand
will resume normal timekeeping when you release the crown button.
To re-enable crown button mode switching
Hold down the crown button as you press A.
If you do not perform any operation for more than three minutes after pulling out the
crown, crown operations will become disabled automatically. If this happens, push
the crown back in and then pull it out again to re-enable crown operations.

Disabling Crown Button Mode Switching

You can use the following operation to disable crown button mode switching.
This helps to prevent accidental mode changes while wearing the watch.
To disable crown button mode switching
Hold down the crown button for at least two seconds until the watch beeps and 1.
then press A.
At this time the x
Second Hand will move to the 3 o’clock position.
Release both buttons.2.
The watch will return to normal timekeeping.
You can use high-speed hand movement when confi guring time settings in the
Timekeeping Mode, Alarm Mode, or Countdown Timer Mode, or when adjusting the
home positions of the hands.
Pushing the Crown In
Carefully press the button of the crown the push the crown back in.
To prevent unintentional operation, the button press operation of the crown
becomes disabled automatically for about eight seconds after you push the crown
back in. It will become re-enabled after about eight seconds.
High-speed 1
With the crown pulled out, rotate it rapidly away from you two times.
High-speed 2
After starting the High-speed 1 operation, rotate the crown rapidly
away from you two more times.
High-speed Cancel
Rotate the crown towards you or press any button.
Pulling the Crown Out
After unlocking the crown, grasp the ring and pull the crown out.
Rotating the Crown
With the crown pulled out, grasp the ring and rotate the crown
towards you to move the hands of the watch.
You can also perform high-speed hand movement using the
operations described below. Note that there are two levels of high-
speed movement (High-speed 2 is faster).
Use High-speed 2 when changing the minute hand setting in the
Timekeeping Mode, Timer Mode, and Alarm Mode.
Note that rotating the ring without pushing it down as far as it will go will change the x
settings of the watch. When locking the crown, be sure to press down fi rmly on the
ring as you rotate it.
Unlocking the Crown
Rotate the ring part of the crown towards you until it loosens
Pressing the Crown Button
You can press the crown button while the crown is locked.
Crown ring

Using the Crown

The crown of this watch has a button part and a ring part. You can use the crown’s
button and ring to perform a number of different crown operations.

Locking the Crown

To lock the crown, push down its ring part as far as it will go as you
rotate the ring away from you until it is relatively tight. While the
crown is locked correctly, the only crown operations possible are
pressing the crown button and unlocking the crown.
Push down on the ring as you slowly rotate it. You should be able to feel it screwing
securely into place.
You should normally have the crown locked during normal daily use. Leaving the x
crown unlocked creates the risk of unintended operations or even damage due to

About This Manual

In this manual, operations are performed using the watch’s
crown, and the three buttons indicated by the letters A,
B and C.

Hands and Indicators

Hour Hand
Second Hand
Minute Hand
Mode Disk: Rotates to indicate the current mode and
other information.
Chronograph Signal
This User’s Guide uses numbers shown above to identify
watch hands and indicators.


Congratulations upon your selection of this CASIO watch.
Note that the product illustrations in this manual are intended for reference only, and so
the actual product may appear somewhat different than depicted by an illustration.
This watch does not have a city code that corresponds to the UTC offset of –3.5
hours. Because of this, the radio-controlled atomic timekeeping function will not
display the correct time for Newfoundland, Canada.
Note that CASIO COMPUTER CO., LTD. assumes no responsibility for any
damage or loss suffered by you or any third party arising through the use of this
product or its malfunction.


Mode d'emploi

Consultez gratuitement le manuel de la marque Casio Edifice EQW-A1000DB-1AER ici. Ce manuel appartient à la catégorie Montres et a été évalué par 8 personnes avec une moyenne de 9.1. Ce manuel est disponible dans les langues suivantes: Anglais. Vous avez une question sur le Edifice EQW-A1000DB-1AER de la marque Casio ou avez-vous besoin d’aide? Posez votre question ici

Besoin d’aide?

Vous avez une question sur le Casio Edifice EQW-A1000DB-1AER et la réponse n'est pas dans le manuel? Posez votre question ici. Fournissez une description claire et complète du problème, et de votre question. Plus votre problème et votre question sont clairement énoncés, plus les autres propriétaires de Casio Edifice EQW-A1000DB-1AER ont de chances de vous fournir une bonne réponse.

Franqueville Frederic • 11-12-2020 Pas de commentaire

Bonjour, je souhaite avoir la référence de la pile . Merci. Salutations

Répondez à cette question

Nombre de questions : 1

Spécifications du Edifice EQW-A1000DB-1AER de la marque Casio

Vous trouverez ci-dessous les spécifications du produit et les spécifications du manuel du Casio Edifice EQW-A1000DB-1AER.

Marque Casio
Modèle Edifice EQW-A1000DB-1AER
Produit Montre
Langue Anglais
Type de fichier Mode d’emploi (PDF)

Foire aux questions

Vous ne trouvez pas la réponse à votre question dans le manuel? Vous trouverez peut-être la réponse à votre question dans la FAQ sur le Casio Edifice EQW-A1000DB-1AER au dessous de.

Votre question n'est pas dans la liste ? Posez votre question ici

Aucun résultat