Casio EQW-500DBE-1AVER

Casio EQW-500DBE-1AVER mode d'emploi

(1)
  • Operation Guide 5041
    1
    MO0806-EA
    Getting Acquainted
    Congratulations upon your selection of this CASIO watch. To get the most out of your
    purchase, be sure to read this manual carefully.
    Starting second hand movement and digital display
    To conserve battery power, the watch is shipped from the
    factory with its functions disabled. Pressing any one of the
    watch’s three buttons will activate its functions, which will
    cause the second hand to start moving and the digital
    display to activate.
    Note that CASIO COMPUTER CO., LTD. assumes no responsibility for any damage
    or loss suffered by you or any third party arising through the use of this product or
    its malfunction.
    About This Manual
    Button operations are indicated using the letters shown
    in the illustration.
    Each section of this manual provides you with the
    information you need to perform operations in each
    mode. Further details and technical information can be
    found in the “Reference” section.
    Hour hand
    Minute hand
    Date
    Second hand
    (Timekeeping/
    Stopwatch)
    24-hour hand
    Stopwatch
    minute hand
    Stopwatch second hand
    Hand Setting Mode Alarm Mode
    World Time Mode
    General Guide
    Press C to change from mode to mode.
    About one or two seconds after you enter the World Time Mode, Alarm Mode, or
    Hand Setting Mode, the hands will move to the position that indicates the current
    setting of the mode.
    In the Timekeeping Mode (except when a setting screen is on the display), press B
    to illuminate the face of the watch for about one second.
    Timekeeping Mode
    Press C.
    Stopwatch Mode
    Radio-controlled Atomic Timekeeping
    This watch receives a time calibration signal and updates its time setting accordingly.
    Supported time calibration signals: Germany (Mainflingen), England (Anthorn).
    See the information under “Signal Reception Troubleshooting” if you experience
    problems with time calibration signal reception.
    Current Time Setting
    This watch adjusts its time setting automatically in accordance with a time calibration
    signal. You also can perform a manual procedure to set the time and date, when
    necessary.
    The first thing you should do after purchasing this watch is to specify your
    Home City, which is the city where you normally will use the watch. For more
    information, see “To specify your Home City”.
    When using the watch outside the areas covered by the time signal transmitters, you
    will have to adjust the current time setting manually as required. See
    “Timekeeping”
    for more information about manual time settings.
    To specify your Home City
    1. In the Timekeeping Mode, hold down A for about five
    seconds until the watch beeps twice.
    The second hand will move to the city code of the
    currently selected Home City. This is the city code
    setting mode.
    2. Use B to move the second hand to the city code you
    want to use as your Home City.
    Each press of B causes the second hand to advance
    clockwise to the next city code.
    Time calibration signal reception is supported when
    any one of the city codes shown in the table below is
    selected as your Home City.
    Second hand
    City code
    For full information on city codes, see the “City Code Table”.
    In addition to the above, you also can select city codes that are outside the ranges
    of the time calibration signal transmitters supported by this watch.
    3. After the Home City setting is the way you want, press A to return to the
    Timekeeping Mode.
    Normally, your watch should show the correct time as soon as you specify your
    Home City code. If it does not, it should adjust automatically after the next auto
    receive operation. You also can perform manual receive or you can set the time
    manually.
    German/U.K. Signal
    City Code
    LON
    PA R
    ATH
    City Name
    London
    Paris
    Athens
    Even if the time calibration signal is received correctly, there are some times when
    the analog hands may not indicate the correct time. If this happens, use the
    procedures under “Adjusting the Home Positions” to check the home positions of the
    hands, and make adjustments as required.
    Time Calibration Signal Reception
    There are two different methods you can use to receive the time calibration signal:
    auto receive and manual receive.
    Auto Receive
    With auto receive, the watch receives the time calibration signal automatically up to six
    times a day. When any auto receive is successful, the remaining auto receive
    operations are not performed. For more information, see “About Auto Receive”.
    Manual Receive
    Manual receive lets you start a time calibration receive operation with the press of a
    button. For more information, see “To perform manual receive”.
    12 o’clock
    or
    Important!
    When getting ready to receive the time calibration signal, position the watch as
    shown in the nearby illustration, with its 12 o’clock side facing towards a window.
    This watch is designed to receive a time calibration signal late at night. Because of
    this, you should place the watch near a window as shown in the illustration when you
    take it off at night. Make sure there are no metal objects nearby.
    Make sure the watch is facing the right way.
    Proper signal reception can be difficult or even impossible under the conditions listed
    below.
    Signal reception normally is better at night than during the day.
    Time calibration signal reception takes from two to seven minutes, but in some
    cases it can take as long as 14 minutes. Take care that you do not perform any
    button operations or move the watch during this time.
    Inside or
    among
    buildings
    Inside a
    vehicle
    Near a
    construction
    site, airport,
    or other
    sources of
    electrical
    noise
    Near high-
    tension power
    lines
    Among or
    behind
    mountains
    Near
    household
    appliances,
    office
    equipment,
    or a mobile
    phone
    Approximate Reception Ranges
    Anthorn
    Mainflingen
    500 kilometers
    1,500 kilometers
    U.K. signal transmitter
    approximate reception
    range as of April 2007
    In April 2007, the U.K. signal transmitter was moved from Rugby to Anthorn, which
    resulted in a slight shift in the approximate reception range of the signal. The shift is
    so slight that there is virtually no change in the ability to receive the signal.
    Even when the watch is within the reception range of a transmitter, signal reception
    may be impossible at times due to the effects of geographic contours, structures,
    weather, the season of the year, the time of day, radio interference, etc. Note that the
    signal becomes weaker at distances of approximately 500 kilometers from the
    transmitter, which means that the influence of the conditions listed above becomes
    even greater.
Casio EQW-500DBE-1AVER

Besoin d’aide?

Nombre de questions : 0

Vous avez une question sur le EQW-500DBE-1AVER de la marque Casio ou avez-vous besoin d’aide? Posez votre question ici. Fournissez une description claire et complète du problème et de votre question. Plus votre problème et votre question sont détaillés, plus il sera facile pour les autres propriétaires du EQW-500DBE-1AVER de la marque Casio de répondre correctement à votre question.

Consultez gratuitement le manuel de la marque Casio EQW-500DBE-1AVER ici. Ce manuel appartient à la catégorie Montres et a été évalué par 1 personnes avec une moyenne de 7.5. Ce manuel est disponible dans les langues suivantes: Engels. Vous avez une question sur le EQW-500DBE-1AVER de la marque Casio ou avez-vous besoin d’aide? Posez votre question ici

Spécifications du EQW-500DBE-1AVER de la marque Casio

Généralités
Marque Casio
Modèle EQW-500DBE-1AVER
Produit Montre
EAN 2601570035805, 4971850899938
Langue Engels
Type de fichier PDF
Détails techniques
Appareil de chronometrage Oui
Fonction heure internationale Oui
Fonction Alarme Oui
Calendrier Oui
Rétroéclairage à LED Oui
Récepteur du signal radio DCF/MSF
Profondeur de l’étanchéité 100 m
Design
Type de verre de montre Minéral
Matériau du boîtier de montre Acier inoxydable
Matière de la bande Résine
Puissance
Type de batterie CR1616
Autonomie batterie 2 année(s)
Nombre de batteries prises en charge 1
Autres caractéristiques
Dimensions (LxPxH) 46 x 13.7 x 49 mm
Poids et dimensions
Poids 91.8 g

Foire aux questions

Ci-dessous, vous trouverez les questions les plus fréquemment posées à propos de Casio EQW-500DBE-1AVER.

Votre question n'est pas dans la liste ? Posez votre question ici

ModesdEmploi.fr

Vous cherchez un manuel ? ModesdEmploi.fr vous permet de trouver le manuel que vous recherchez en un rien de temps. Notre base de données contient plus d'un million de manuels en PDF pour plus de 10 000 marques. Chaque jour, nous ajoutons les derniers manuels afin que vous trouviez toujours le produit que vous recherchez. C'est très simple : entrez le nom de la marque et le type de produit dans la barre de recherche pour consulter gratuitement et immédiatement le manuel de votre choix en ligne.

ModesdEmploi.fr

© Copyright 2021 ModesdEmploi.fr. Tous droits réservés.

Nous utilisons des cookies pour vous garantir la meilleure expérience sur notre site. Si vous continuez à utiliser ce dernier, nous considérerons que vous acceptez l'utilisation des cookies.