Casio EQW-M1100DB-1AER

Casio EQW-M1100DB-1AER mode d'emploi

(2)
  • 1
    Operation Guide 5122
    MA1005-EA
    Congratulations upon your selection of this CASIO watch.
    This watch does not have a city code that corresponds to the UTC offset of –3.5
    hours. Because of this, the radio-controlled atomic timekeeping function will not
    display the correct time for Newfoundland, Canada.
    Note that CASIO COMPUTER CO., LTD. assumes no responsibility for any
    damage or loss suffered by you or any third party arising through the use of this
    product or its malfunction.
    About This Manual
    Left Dial hand
    
    B +
    *> 56
    @
    Button operations are indicated using the letters A
    through D shown in the illustration.
    Hand Functions
    z Hour Hand
    x Second Hand
    c Minute Hand
    v Left Dial hand:
    Indicates the current mode (TM, ST, WT, AL).
    b Right Dial Hands:
    Indicate a time, in 24-hour format,
    depending on the current mode.
    n 24-hour Hand:
    Indicates the current 24-hour timekeeping hour.
    m Day
    This User’s Guide uses numbers shown above to identify
    watch hands and indicators.
    Things to check before using the watch
    1. Hold down C at least two seconds to enter the Timekeeping Mode, and
    then observe the movement of the
    x Second Hand.
    Is the x Second Hand moving smoothly at one-second intervals?
    Is the x Second Hand moving at
    two-second intervals or is it stopped
    completely?
    Go to step 2.
    The watch is charged sufficiently.
    For details about charging, see
    “Charging the Watch”.
    Power is low. Charge the watch by placing
    it in a location where it is exposed to light.
    For details, see “Charging the Watch”.
    NO
    YES
    YES
    NEXT
    2. Check the Home City and the daylight saving time (DST) setting.
    Use the procedure under “To configure summer time and other Home City settings” to
    configure your Home City and daylight saving time settings.
    Important!
    Proper time calibration signal reception and World Time settings depend on correct
    Home City, time, and date settings in the Timekeeping Mode. Make sure you
    configure these settings correctly.
    3. Set the current time.
    To set the time using a time calibration signal
    See “To get ready for a receive operation”.
    To set the time manually
    See “Configuring Current Time and Date Settings Manually”.
    The watch is now ready for use.
    For details about the watch’s radio controlled timekeeping feature, see “Radio
    Controlled Atomic Timekeeping”.
    Charging the Watch
    The face of the watch is a solar cell that generates power from light. The generated
    power charges a built-in rechargeable battery, which powers watch operations. The
    watch charges whenever it is exposed to light.
    Charging Guide
    Whenever you are not
    wearing the watch, leave
    it in a location where it is
    exposed to light.
    Best charging
    performance is achieved
    by exposing the watch to
    light that is as strong as
    possible.
    When wearing the watch,
    make sure that its face is
    not blocked from light by the
    sleeve of your clothing.
    The watch may enter a
    sleep state if its face is
    blocked by your sleeve
    even only partially.
    Warning!
    Leaving the watch in bright light for charging can cause it to become quite hot.
    Take care when handling the watch to avoid burn injury. The watch can become
    particularly hot when exposed to the following conditions for long periods.
    On the dashboard of a car parked in direct sunlight
    Too close to an incandescent lamp
    Under direct sunlight
    Important!
    Keep the watch in an area normally exposed to bright light when storing it for long
    periods. This helps to ensure that power does not run down.
    Storing the watch for long periods in an area where there is no light or wearing it in
    such a way that it is blocked from exposure to light can cause power to run down.
    Make sure that the watch is exposed to bright light whenever possible.
    Power Levels
    You can get an idea of the watch’s power level by
    observing the movement of the
    x Second Hand in the
    Timekeeping Mode.
    If the
    x Second Hand is moving normally at one-second
    intervals, power is at Level 1.
    If the
    x Second Hand is moving at two-second intervals,
    power is at Level 2, which is quite low. Expose the watch
    to light as soon as possible so it can charge.
    Level Hand Movement Function Status
    1 Normal. All functions enabled
    2
    x Second Hand moves at two-second
    intervals.
    m Day changes to 1 (home position).
    Beeper, time calibration signal
    reception disabled
    3
    x Second Hand stopped.
    z Hour Hand and c Minute Hand
    stopped at 12 o’clock.
    All functions disabled
    When power drops to Level 3, all functions will be disabled but the watch will
    continue to keep time internally for about one week. If you recharge the battery
    sufficiently during this period, the analog hands will move automatically to the
    correct setting and regular timekeeping will resume. After one week, all settings
    (including timekeeping) will be cleared. Recharging the battery will reset all settings
    to their initial factory defaults.
    Power Recovery Mode
    The watch is designed to go into a power recovery mode that stops hand operation
    temporarily whenever power suddenly drops below a certain level due to overuse
    of the alarm tone over a short period. Note that all operations are disabled while the
    watch is in the power recovery mode.
    The hands will move to the correct positions and the watch will resume normal
    operation after power recovers (in about 15 minutes). Putting the watch in a location
    where it is exposed to light will help power to recover sooner.
    Charging Times
    Exposure Level (Brightness)
    Daily
    Operation
    *1
    Level Change *2
    Level 3 Level 2 Level 1
    Outdoor sunlight (50,000 lux) 8 minutes 2 hours 23 hours
    Window sunlight (10,000 lux) 30 minutes 6 hours 85 hours
    Window sunlight on cloudy day
    (5,000 lux)
    48 minutes 8 hours 138 hours
    Indoor fluorescent lighting (500 lux) 8 hours 92 hours – – –
    1 Approximate exposure each day to generate power for normal daily operation. *
    2 Approximate exposure to take power up one level. *
    The above times are for reference only. Actual times depend on lighting conditions.
    For details about the operating time and daily operating conditions, see the “Power
    Supply” section of the Specifications.
    Power Saving
    Power Saving enters a sleep state automatically whenever the watch is left for a
    certain period in an area where it is dark. The table below shows how watch functions
    are affected by Power Saving.
    There actually are two sleep state levels: “second hand sleep” and “function sleep”.
    Elapsed Time in Dark Operation
    60 to 70 minutes (second hand sleep)
    x Second Hand only stopped at 12 o’clock, all
    other functions enabled
    6 or 7 days (function sleep)
    All functions, including analog timekeeping,
    disabled
    Internal timekeeping maintained
    The watch will not enter a sleep state between 6:00 AM and 9:59 PM. If the watch
    is already in a sleep state when 6:00 AM arrives, however, it will remain in the sleep
    state.
    The watch will not enter a sleep state while it is in the Stopwatch Mode.
    To recover from the sleep state
    Move the watch to a well-lit area or press any button.
    Radio Controlled Atomic Timekeeping
    This watch receives a time calibration signal and updates its time setting accordingly.
    However, when using the watch outside of areas covered by time calibration signals,
    you will have to adjust the settings manually as required. See “Configuring Current
    Time and Date Settings Manually” for more information.
    This section explains how the watch updates its time settings when the city code
    selected as the Home City is in Japan, North America, Europe, or China, and is one
    that supports time calibration signal reception.
    If your Home City code setting is this:
    The watch can receive the signal from the
    transmitter located here:
    LON, PAR, ATH Anthorn (England), Mainflingen (Germany)
    HKG Shangqiu City (China)
    TYO Fukushima (Japan), Fukuoka/Saga (Japan)
    HNL, ANC, LAX, DEN, CHI, NYC Fort Collins, Colorado (United States)
    Important!
    The areas covered by HNL and ANC are quite far from the calibration signal
    transmitters, so certain conditions may cause reception problems.
    When HNL or HKG is selected as the Home City, only the time and date are
    adjusted according to the time calibration signal. You need to switch manually
    between standard time and daylight saving time (DST) if required.
    See “To configure summer time and other Home City settings” for information about
    how to do this.
    Moves at two-second
    intervals.
    
    @
    B +
    5
Casio EQW-M1100DB-1AER

Besoin d’aide?

Nombre de questions : 0

Vous avez une question sur le EQW-M1100DB-1AER de la marque Casio ou avez-vous besoin d’aide? Posez votre question ici. Fournissez une description claire et complète du problème et de votre question. Plus votre problème et votre question sont détaillés, plus il sera facile pour les autres propriétaires du EQW-M1100DB-1AER de la marque Casio de répondre correctement à votre question.

Consultez gratuitement le manuel de la marque Casio EQW-M1100DB-1AER ici. Ce manuel appartient à la catégorie Montres et a été évalué par 2 personnes avec une moyenne de 9.1. Ce manuel est disponible dans les langues suivantes: Engels. Vous avez une question sur le EQW-M1100DB-1AER de la marque Casio ou avez-vous besoin d’aide? Posez votre question ici

Spécifications du EQW-M1100DB-1AER de la marque Casio

Généralités
Marque Casio
Modèle EQW-M1100DB-1AER
Produit Montre
EAN 2601570038776
Langue Engels
Type de fichier PDF
Détails techniques
Appareil de chronometrage Oui
Fonction heure internationale Oui
Fonction Alarme Oui
Calendrier Oui
Récepteur du signal radio DCF/MSF/WWVB/JJY/BPC
Profondeur de l’étanchéité 100 m
Puissance
Énergie solaire Oui
Type de batterie CTL920
Design
Type de verre de montre Minéral
Matériau du boîtier de montre Acier inoxydable
Matière de la bande Résine
Autres caractéristiques
Dimensions (LxPxH) 46.9 x 13.7 x 51.5 mm
Poids et dimensions
Poids 110 g

Foire aux questions

Ci-dessous, vous trouverez les questions les plus fréquemment posées à propos de Casio EQW-M1100DB-1AER.

Votre question n'est pas dans la liste ? Posez votre question ici

ModesdEmploi.fr

Vous cherchez un manuel ? ModesdEmploi.fr vous permet de trouver le manuel que vous recherchez en un rien de temps. Notre base de données contient plus d'un million de manuels en PDF pour plus de 10 000 marques. Chaque jour, nous ajoutons les derniers manuels afin que vous trouviez toujours le produit que vous recherchez. C'est très simple : entrez le nom de la marque et le type de produit dans la barre de recherche pour consulter gratuitement et immédiatement le manuel de votre choix en ligne.

ModesdEmploi.fr

© Copyright 2021 ModesdEmploi.fr. Tous droits réservés.

Nous utilisons des cookies pour vous garantir la meilleure expérience sur notre site. Si vous continuez à utiliser ce dernier, nous considérerons que vous acceptez l'utilisation des cookies.