Casio GW-2500B-1AER mode d'emploi

Casio GW-2500B-1AER
8.3 · 5
PDF mode d'emploi
 · 7 pages
Anglais
mode d'emploiCasio GW-2500B-1AER

Operation Guide 5064

1
MO0905-EA
Getting Acquainted
Congratulations upon your selection of this CASIO watch. To get the most out of your
purchase, be sure to read this manual carefully.
Keep the watch exposed to bright light
The electricity generated by the solar cell of the watch is
stored by a built-in battery. Leaving or using the watch
where it is not exposed to light causes the battery to run
down. Make sure the watch is exposed to light as much as
possible.
When you are not wearing the watch on your wrist,
position the face so it is pointed at a source of bright
light.
You should try to keep the watch outside of your sleeve
as much as possible. Charging is reduced significantly if
the face is even only partially covered.
l
l
l
l
l
l
l
l
l
l
l
Bright Light
Solar cell
The watch continues to operate, even when it is not exposed to light. Leaving the
watch in the dark can cause the battery to run down, which will result in some watch
functions to be disabled. If the battery goes dead, you will have to re-configure watch
settings after recharging. To ensure normal watch operation, be sure to keep it
exposed to light as much as possible.
All
functions
enabled
LEVEL 1
LEVEL 2
LEVEL 3
LEVEL 4
Charge
Rechargeable battery
Bright Light
Electrical
energy
Solar cell
(Converts light to
electrical power.)
Some or all
functions
disabled
LEVEL 1
LEVEL 2
LEVEL 3
LEVEL 4
Dis-
charge
Battery charges in the light. Battery discharges in the dark.
The actual level at which some functions are disabled depends on the watch model.
Frequent display illumination can run down the battery quickly and require charging.
The following guidelines give an idea of the charging time required to recover from a
single illumination operation.
Approximately 5 minutes exposure to bright sunlight coming in through a window
Approximately about 8 hours exposure to indoor fluorescent lighting
Be sure to read “Power Supply” for important information you need to know
when exposing the watch to bright light.
If the display of the watch is blank...
If the display of the watch is blank, it means that the watch’s Power Saving function
has turned off the display to conserve power.
See “Power Saving Function” for more information.
Note that CASIO COMPUTER CO., LTD. assumes no responsibility for any
damage or loss suffered by you or any third party arising through the use of this
product or its malfunction.
About This Manual
Depending on the model of your watch, display text
appears either as dark figures on a light background or
light figures on a dark background. All sample displays
in this manual are shown using dark figures on a light
background.
Button operations are indicated using the letters shown
in the illustration.
Each section of this manual provides you with the
information you need to perform operations in each
mode. Further details and technical information can be
found in the “Reference” section.
General Guide
Press C to change from mode to mode.
In any mode (except a setting mode), press B to illuminate the display for about
one second.
Timekeeping Mode
Press C.
Alarm Mode Countdown Timer Mode
World Time Mode Stopwatch Mode
Radio-controlled Atomic Timekeeping
This watch receives a time calibration signal and updates its time setting accordingly.
This watch is designed to pick up the time calibration signals transmitted in Germany
(Mainflingen), England (Anthorn), the United States (Fort Collins), China
(Shangqiu), and Japan (Fukushima, Fukuoka/Saga).
See the information under “Signal Reception Troubleshooting” if you experience
problems with time calibration signal reception.
Current Time Setting
This watch adjusts its time setting automatically in accordance with a time calibration
signal. You also can perform a manual procedure to set the time and date, when
necessary.
The first thing you should do after purchasing this watch is to specify your
Home City (the city where you normally will use the watch). For more
information, see “To specify your Home City”.
When using the watch outside the areas covered by the time signal transmitters, you
will have to adjust the current time setting manually as required. See
“To set the time
and date manually” for more information about manual time settings.
The U.S. time calibration signal can be picked up by the watch while in North
America. The term “North America” in this manual refers to the area that consists of
Canada, the continental United States, and Mexico.
As of January 2008, China does not use Daylight Saving Time (DST). If China does
go to the Daylight Saving Time system in the future, some functions of this watch
may no longer operate correctly.
To specify your Home City
1. In the Timekeeping Mode, hold down A for about five
seconds until the left dial hand points to T1 and the city
code flashes on the upper display. This is the setting
mode.
2. Press D (east) and B (west) to select the city code
you want to use as your Home City.
LIS, LON : Lisbon, London
MAD, PAR , ROM, BER, STO : Madrid, Paris, Rome,
Berlin, Stockholm
ATH : Athens
MOW : Moscow
HKG, BJS, TPE : Hong Kong, Beijing, Taipei
SEL, TYO : Seoul, Tokyo
HNL : Honolulu
ANC : Anchorage
YVR, LAX : Vancouver, Los Angeles
l
l
l
l
l
l
l
l
l
l
l
l
l
l
City code
Hour : Minutes
PM indicator
Seconds
Left dial
hand
YEA, DEN : Edmonton, Denver
MEX, CHI : Mexico City, Chicago
MIA, YTO, NYC : Miami, Toronto, New York
YHZ : Halifax
YYT : St.Johns
3. Press A twice to exit the setting mode.
Normally, your watch should show the correct time as soon as you select your Home
City code. If it does not, it should adjust automatically after the next auto receive
operation (in the middle of the night). You also can perform manual receive or you
can set the time manually.
The watch will receive the time calibration signal automatically from the applicable
transmitter (in the middle of the night) and update its settings accordingly. For
information about the relationship between city codes and transmitters, see
“Important!” under “Time Calibration Signal Reception” and “Transmitters”.
See the maps under “Approximate Reception Ranges” for information about the
reception ranges of the watch.
Time Calibration Signal Reception
There are two different methods you can use to receive the time calibration signal:
auto receive and manual receive.
Auto Receive
With auto receive, the watch receives the time calibration signal automatically up to six
times a day (five times for the China signal). When any auto receive is successful,
remaining auto receive operations are not performed. For more information, see
“About Auto Receive”.
Manual Receive
Manual receive lets you start a time calibration receive operation with the press of a
button. For more information, see “To perform manual receive”.
Important!
When getting ready to receive the time calibration signal, position the watch as
shown in the nearby illustration, with its 12 o’clock side pointing towards a window.
This watch is designed to receive a time calibration signal late at night. Because of
this, you should place the watch near a window as shown in the illustration when you
take it off at night. Make sure there are no metal objects nearby.
12 o’clock
or
Make sure the watch is facing the right way.

Mode d'emploi

Consultez gratuitement le manuel de la marque Casio GW-2500B-1AER ici. Ce manuel appartient à la catégorie Montres et a été évalué par 5 personnes avec une moyenne de 8.3. Ce manuel est disponible dans les langues suivantes: Anglais. Vous avez une question sur le GW-2500B-1AER de la marque Casio ou avez-vous besoin d’aide? Posez votre question ici

Besoin d’aide?

Vous avez une question sur le Casio GW-2500B-1AER et la réponse n'est pas dans le manuel? Posez votre question ici. Fournissez une description claire et complète du problème, et de votre question. Plus votre problème et votre question sont clairement énoncés, plus les autres propriétaires de Casio GW-2500B-1AER ont de chances de vous fournir une bonne réponse.

Nombre de questions : 0

Spécifications du GW-2500B-1AER de la marque Casio

Vous trouverez ci-dessous les spécifications du produit et les spécifications du manuel du Casio GW-2500B-1AER.

Généralités
Marque Casio
Modèle GW-2500B-1AER | GW-2500B-1AER
Produit Montre
Langue Anglais
Type de fichier Mode d’emploi (PDF)
Détails techniques
Appareil de chronometrage Oui
Fonction heure internationale Oui
Fonction 1/1min - 1h
Fonction Alarme Oui
Calendrier Oui
Rétroéclairage à LED Oui
Résistant aux chocs Oui
Fonction Snooze Oui
Mode horloge 12h/24h
Récepteur du signal radio DCF/MSF/WWVB/JJY/BPC
Profondeur de l’étanchéité 200 m
Puissance
Énergie solaire Oui
Type de batterie CTL920
Indicateur du niveau de recharge Oui
Nombre de batteries prises en charge 1
Design
Type de verre de montre Minéral
Matériau du boîtier de montre Acier inoxydable
Matière de la bande Résine
Autres caractéristiques
Dimensions (LxPxH) 46.9 x 15.8 x 47 mm
Poids et dimensions
Poids 66 g
voir plus

Foire aux questions

Vous ne trouvez pas la réponse à votre question dans le manuel? Vous trouverez peut-être la réponse à votre question dans la FAQ sur le Casio GW-2500B-1AER au dessous de.

Votre question n'est pas dans la liste ? Posez votre question ici

Aucun résultat