CyberPower BR650ELCD

CyberPower BR650ELCD mode d'emploi

(1)
  • BR450ELCD/BR650ELCD/BR850ELCD
    Users Manual
    K01-0000056-00
    SAFETY WARNINGS
    (SAVE THESE INSTRUCTIONS)
    This manual contains important safety instructions. Please read and follow all instructions carefully
    during installation and operation of the unit. Read this manual thoroughly before attempting to unpack,
    install, or operate your UPS.
    This equipment can be operated by any individuals with no previous training.
    The socket-outlet shall be installed near the equipment and easily accessible.
    During the installation of this equipment it should be assured that the sum of the leakage currents of the
    UPS and the connected loads does not exceed 3.5mA.
    Attention, hazardous through electric shock. Also with disconnection of this unit from the mains,
    hazardous voltage still may be accessible through supply from battery. The battery supply should be
    therefore disconnected in the plus and minus pole at the quick connectors of the battery when
    maintenance or service work inside the UPS is necessary.
    Do not dispose of batteries in a fire, the battery may explode.
    Do not open or mutilate the battery or batteries, released electrolyte is harmful to the skin and eyes.
    INSTALLING YOUR UPS SYSTEM
    UNPACKING
    Inspect the UPS upon receipt. The box should contain the following:
    (1)UPS Unit¯1; (1)Phone Line¯1;(3)USB Cable¯1;(4)User Manual¯1;(5)Management software
    Disk¯1;(6)Green Power Technology description¯1;(7)Battery Charger¯1;(8)Cable Collector¯1
    HOW TO DETERMINE THE POWER REQUIREMENTS OF YOUR EQUIPMENT
    1. Insure that the equipment plugged into the battery power-supplied outlets does not exceed the UPS
    unit’s rated capacity (450VA/270W for BR450ELCD, 650VA/390W for BR650ELCD, 850VA/510W for
    BR850ELCD). If rated unit capacities are exceeded, an overload condition may occur and cause the
    UPS unit to shut down or the fuse blow.
    2. If the power requirements of your equipment are listed in units other than Volt-Amps (VA), convert
    Watts (W) or Amps (A) into VA by doing the calculations below. Note: The below equation only
    calculates the maximum amount of VA that the equipment can use, not what is typically used by the
    equipment at any one time. Users should expect usage requirements to be approximately 60% of
    below value.
    TO ESTIMATE POWER REQUIREMENTS
    1.
    Watts (W) x 1.67 = VA or Amps (A) x 230 = VA
    2. Add the totals up for all pieces of equipment and multiply this total by 0.6 to calculate actual
    requirements. There are many factors that can affect the amount of power that your computer system
    will require. Suggest the total load to be placed on the battery-powered outlets should not exceed
    80% of the unit’s capacity.
    HARDWARE INSTALLATION GUIDE
    Before installation, please
    read and understand the following instructions:
    1. Placement
    The UPS must be installed in a protected environment away from heat- emitting appliances such
    as a radiator or heat register. Do not install this product where excessive moisture is present.
    2. Ventilation
    The location should provide adequate air flow around the UPS with one inch minimum clearance
    on all sides for proper ventilation.
    3. Charge the Battery
    Your new UPS may be used immediately upon receipt. However charge loss may occur during
    shipping and storage. So charging the battery for at least 8 hours is recommended to insure that
    the battery is fully charged. (To recharge the battery, simply leave the unit plugged into an AC
    outlet.)
    This UPS can be charged even when UPS is not turn on.
    4. Connect to AC
    Use power cord to connect
    the UPS to a wall outlet. Please avoid
    using extension cords and adapter
    plugs. (To maintain optimal battery
    charge, leave the UPS plugged in at
    all times.)
    5. Connect the Load
    Connect the equipment to your UPS
    outlets. The IEC power cord coming
    with the unit are used to connect your
    computer and monitor to the UPS.
    Items such as copiers, laser
    printers, vacuums, space heaters,
    or other large electrical devices
    SHOULD NOT be connected to the
    UPS. Please make sure that the total
    loads of your equipments are less than the maximum total power load of your UPS.
    6. Connect to Computer
    Install your software and accessories. To use the software, simply use the USB cable to connect
    the UPS unit and your computer.
    BASIC OPERATION
    1. Power On/Off Switch
    Press the power switch to turn the UPS ON or OFF.
    2. LCD Function Selected Switch
    Press the LCD function selected switch to know the UPS status.
    3. LCD Display
    The LCD will display the UPS status including input voltage, output voltage, runtime, percentage of
    load and battery…etc.
    4. Communication Protection Ports RJ11/RJ45
    Communication protection ports will protect any standard modem, fax, telephone line, or network
    cable from surge and spikes.
    5. Battery Charger port
    Charge external AA/AAA battery via battery charger port with battery charger.
    6. AC outlet
    The UPS provides 3 outlets for connected equipment to insure temporary uninterrupted operation
    during a power failure and against surges and spikes and another 3 outlets against surges and spikes
    only.
    7. USB Port to PC
    This port allows connection and communication
    from the USB port on the computer to the UPS
    unit. The UPS communicates its status to the
    PowerPanel
    ®
    Personal Edition software. This
    interface is also compatible with the UPS service
    provided by Windows NT, Windows 2000,
    Windows XP, Windows Vista. Mac OSX, Linux.
    8. Input Circuit Breaker
    The Circuit Breaker provides optimal overload protection.
    9 Power on LED
    The power on LED lights up when the UPS is ON.
    10 Cable Collector
    Collect the cables connected from the AC outlets in the cable collector.
    11 Battery Charger
    Put external AA/AAA batteries into the battery charger for charge.
CyberPower BR650ELCD

Besoin d’aide?

Nombre de questions : 0

Vous avez une question sur le BR650ELCD de la marque CyberPower ou avez-vous besoin d’aide? Posez votre question ici. Fournissez une description claire et complète du problème et de votre question. Plus votre problème et votre question sont détaillés, plus il sera facile pour les autres propriétaires du BR650ELCD de la marque CyberPower de répondre correctement à votre question.

Consultez gratuitement le manuel de la marque CyberPower BR650ELCD ici. Ce manuel appartient à la catégorie Alimentations d'énergie non interruptible et a été évalué par 1 personnes avec une moyenne de 5.7. Ce manuel est disponible dans les langues suivantes: Anglais. Vous avez une question sur le BR650ELCD de la marque CyberPower ou avez-vous besoin d’aide? Posez votre question ici

Spécifications du BR650ELCD de la marque CyberPower

Généralités
Marque CyberPower
Modèle BR650ELCD
Produit Alimentation d'énergie non interruptible
EAN 4712364141140, 4712364142338, 4712364142512, 4712364146992
Langue Anglais
Type de fichier PDF
Caractéristiques
capacité de la puissance de sortie 650
Puissance de sortie 390
Tension de voltage à l'entrée (min) 160
Tension de voltage à l'entrée (max) 265
tension de voltage à la sortie (min) -
Tension de voltage à la sortie (max) -
Fréquence d'entrée 47/63
Topologie UPS -
Protection contre les surtensions
Fonctions de protection de surtensions Fax, Modem, Network, Telephone
Dispositifs de protection électrique Surcharge
Régulateur de tension automatique (AVR)
Alarmes sonores
Connectivité
Nombre de prises en sortie 6
Types de sortie AC -
Ports (RJ11) du modem 1
Quantité de Ports USB 2.0 1
Nombre de port ethernet LAN (RJ-45) 1
Batterie
Temps de rechargement de la batterie 8
Temps de secours type à demi de charge 9
Temps de secours type au chargement complet 2
Design
Format -
Couleur du produit Noir
Écran LCD
Voyants
Poids et dimensions
Largeur 271
Profondeur 160.7
Hauteur 113.6
Poids 5500

ModesdEmploi.fr

Vous cherchez un manuel ? ModesdEmploi.fr vous permet de trouver le manuel que vous recherchez en un rien de temps. Notre base de données contient plus d'un million de manuels en PDF pour plus de 10 000 marques. Chaque jour, nous ajoutons les derniers manuels afin que vous trouviez toujours le produit que vous recherchez. C'est très simple : entrez le nom de la marque et le type de produit dans la barre de recherche pour consulter gratuitement et immédiatement le manuel de votre choix en ligne.

ModesdEmploi.fr

© Copyright 2020 ModesdEmploi.fr. Tous droits réservés.

Nous utilisons des cookies pour vous garantir la meilleure expérience sur notre site. Si vous continuez à utiliser ce dernier, nous considérerons que vous acceptez l'utilisation des cookies.

En savoir plus