CyberPower CP1500PFCLCD

CyberPower CP1500PFCLCD mode d'emploi

(1)
  • CP1350PFCLCD
    CP1500PFCLCD
    Users Manual
    K01-0000162-00
    (SAVE THESE INSTRUCTIONS)
    This manual contains important safety instructions. Please read and follow all instructions carefully during installation and operation of the unit.
    Read this manual thoroughly before attempting to unpack, install, or operate your UPS.
    CAUTION! To prevent the risk of fire or electric shock, install in a temperature and humidity controlled indoor area free of conductive
    contaminants. (Please see specifications for acceptable temperature and humidity range).
    CAUTION! To reduce the risk of electric shock, do not remove the cover except to service the battery. Turn off and unplug the unit before
    servicing the batteries. There are no user serviceable parts inside except for the battery.
    CAUTION! Hazardous live parts inside can be energized by the battery even when the AC input power is disconnected.
    CAUTION! The UPS must be connected to an AC power outlet with fuse or circuit breaker protection. Do not plug into an outlet that is not
    grounded. If you need to de-energize this equipment, turn off and unplug the unit.
    CAUTION! To avoid electric shock, turn off the unit and unplug it from the AC power source before servicing the battery or installing a computer
    component.
    CAUTION! Not for use in a computer room as defined in the Standard for the Protection of Electronic Computer/Data Processing Equipment,
    ANSI/NFPA 75.
    CAUTION! To reduce the risk of fire, connect only to a circuit provided with 20 amperes maximum branch circuit over current protection in
    accordance with the National Electric Code, ANSI/NFPA 70.
    DO NOT USE FOR MEDICAL OR LIFE SUPPORT EQUIPMENT! CyberPower Systems does not sell products for life support or medical
    applications. DO NOT use in any circumstance that would affect the operation and safety of life support equipment, medical applications, or
    patient care.
    DO NOT USE WITH OR NEAR AQUARIUMS! To reduce the risk of fire or electric shock, do not use with or near an aquarium. Condensation
    from the aquarium can cause the unit to short out.
    INTRODUCTION
    Thank you for selecting a CyberPower Systems UPS product. This UPS is designed to provide unsurpassed power protection, operation and
    performance during the lifetime of the product.
    UNPACKING
    Inspect the UPS upon receipt. The box should contain the following:
    (a) UPS unit x 1 (b) Users manual x 1 (c) Telephone cable x 1 (d) PowerPanel
    ®
    Personal Edition software CD x 1 (e) Coaxial cable x 1
    (f) USB A+B type cable x 1 (g) Warranty registration card x 1 (h) Function Setup Guide x 1
    SUPPORTS Active PFC POWER SUPPLIES
    This CyberPower UPS system supports High Efficiency power supplies with Active Power Factor Correction (Active PFC). Active PFC is used to
    improve the efficiency of power delivery. The current US Energy Star
    ®
    Program Requirements for Computers (version 5.0) mandates Active PFC
    for all power supplies over 100 watts. Additionally, programs such as 80 Plus
    ®
    are often used to identify high efficiency power supplies with Active
    PFC.
    OVERVIEW
    The CP1350PFCLCD/CP1500PFCLCD provides complete power protection from utility power that is not
    always consistent. The CP1350PFCLCD/CP1500PFCLCD features 1030 Joules of surge protection. Both
    units provide long lasting battery backup during power outages with maintenance free batteries. The
    CP1350PFCLCD/CP1500PFCLCD ensures consistent power to your computer system and includes software
    that will automatically save your open files and shutdown your computer system during a utility power loss.
    AUTOMATIC VOLTAGE REGULATOR
    The CP1350PFCLCD/CP1500PFCLCD stabilizes inconsistent utility power voltage to nominal levels that are safe for equipment. Inconsistent
    incoming utility power may be damaging to important data files and hardware, but with Automatic Voltage Regulation (AVR), damaging voltage
    levels are corrected to safe levels. AVR automatically increases low utility power and decreases high utility power to a consistent and safe
    110/120 volts. If incoming utility voltage drops below 90 volts, or exceeds 140 volts the units automatically switch to battery back-up power.
    HOW TO DETERMINE THE POWER REQUIREMENTS OF YOUR EQUIPMENT
    1. Ensure that the equipment plugged into the outlet does not exceed the UPS unit’s rated capacity (1350VA/810W for CP1350PFCLCD,
    1500VA/900W for CP1500PFCLCD). If the rated capacities of the unit are exceeded, an overload condition may occur and cause the UPS
    unit to shut down or the circuit breaker to trip.
    2. There are many factors that can affect the amount of power that your computer system will require. It is suggested that the load placed on
    the battery outlets not exceed 80% of the unit’s capacity.
    HARDWARE INSTALLATION GUIDE
    1. Your new UPS may be used immediately upon receipt. However, after receiving a new UPS, to ensure the
    battery’s maximum charge capacity, it is recommended that you charge the battery for at least 8 hours.
    Your UPS is equipped with an auto-charge feature. When the UPS is plugged into an AC outlet, the
    battery will automatically charge when it’s turned on or turned off.
    2. With the UPS unit turned off and unplugged, connect your computer, monitor, and any other peripherals
    requiring battery backup into the battery power supplied outlets. For pluggable equipment, the socket-outlet
    shall be installed near the equipment and shall be easily accessible. DO NOT plug a laser printer, paper shredder, copier, space heater,
    vacuum, sump pump or other large electrical devices into the “Battery and Surge Protected Outlets”. The power demands of these
    devices may overload and damage the unit.
    3. To protect a fax, phone or modem, connect a telephone cable or network cable from the wall jack outlet to the IN
    jack of the UPS. Connect a telephone cable or network cable from the OUT jack of the UPS to a fax machine,
    telephone, modem, or network devices.
    4. Plug the UPS into a 2 pole, 3 wire grounded receptacle (wall outlet). Make sure the wall branch outlet is
    protected by a fuse or circuit breaker and does not service equipment with large electrical demands (e.g. air
    conditioner, copier, etc…). The warranty prohibits the use of extension cords, outlet strips, and surge strips.
    5. Press the power switch to turn the unit on. The Power On indicator light will illuminate and the unit will “beep”.
    If an overload is detected, an audible alarm will sound and the unit will emit one long beep. To correct this, turn the UPS off and unplug at
    least one piece of equipment from the battery power supplied outlets. Make sure the circuit breaker is depressed and then turn the UPS on.
    6. To maintain optimal battery charge, leave the UPS plugged into an AC outlet at all times.
    7. To store the UPS for an extended period, cover it and store with the battery fully charged. While in storage, recharge the battery every three
    months to ensure battery life.
    DESCRIPTION
    1 Power Switch
    Used as the master on/off switch for equipment connected to the battery power supplied outlets.
    2 Power On Indicator
    This LED is illuminated when the utility power is normal and the UPS outlets are providing power, free of surges and spikes.
    3 LCD module display
    High resolution and intelligent LCD display shows all the UPS information using icons and messages. For more information please review
    the “Definitions for Illuminated LCD Indicators” section below.
    4 Display switch
    The switch can be used to select the LCD display contents including Input Voltage, Output Voltage, and Estimated Run Time. The toggle
    frequency is set to one time per 0.5 second. Press the switch to roll down the function menu. Press the switch for 2 seconds can turn on or
    turn off the LCD display in Line Mode.
    5 Silence Alarm switch
    The toggle frequency is set to one time per 0.5 second. Press the switch to roll up the function menu. Holding the switch for more than 2
    seconds while running on battery will silence the buzzer.
    6 Control switch
    Press the Control switch for 3 seconds in Line Mode to perform a Self Test of the battery.
    7 USB Power Ports
    The USB Power ports provide 5V 1A power output.
    8 Battery and Surge Protected Outlets
    The unit has five battery powered/surge suppression outlets for connected equipment to ensure temporary uninterrupted operation of your
    equipment during a power failure. (DO NOT plug a laser printer, paper shredder, copier, space heater, vacuum, sump pump or other
    large electrical devices into the “Battery and Surge Protected Outlets”. The power demands of these devices may overload and
    damage the unit.)
    9 Full-Time Surge Protection Outlets
    The unit has five surge suppression outlets.
    10 Circuit Breaker
    Located on the back of the UPS, the circuit breaker serves to provide overload and fault protection.
    11 Serial/USB Ports to PC
    The USB port allows connection and communication between the USB port on the computer and the UPS unit.
    12 Communication Protection Ports
    Communication protection ports will protect any standard modem, fax, telephone line, network or Ethernet connection (RJ11/RJ45).
    13 Wiring Fault Indicator (red)
    This LED indicator will illuminate to warn the user that a wiring problem exists, such as bad ground, missing ground or reversed wiring. If
    this is illuminated, disconnect all electrical equipment from the outlet and have an electrician verify the outlet is properly wired. The unit will
    not provide surge protection without being plugged into a grounded and properly wired wall outlet.
    14 Coax/Cable/DSS Surge Protection
    The Coax/Cable/DSS protection ports will protect any cable modem, CATV converter, or DSS receiver.
    15 Outlets Designed for AC Adapters
    The unit has two outlets spaced to allow AC power adapter blocks to be plugged into the UPS without blocking adjacent outlets.
    REPLACING THE BATTERY
    Replacement of batteries located in an OPERATOR ACCESS AREA.
    1. When replacing batteries, replace with the same number of the following battery: CyberPower / RB1270X2A for the CP1350PFCLCD;
    CyberPower / RB1280X2A for the CP1500PFCLCD.
    2. CAUTION! Risk of Energy Hazard, 24 V, maximum 9 Ampere-hour battery. Before replacing batteries, remove conductive jewelry such
    as chains, wrist watches, and rings. High energy conducted through these materials could cause severe burns.
    3. CAUTION! Do not dispose of batteries in a fire. The batteries may explode.
    4. CAUTION! Do not open or mutilate batteries. Released material is harmful to the skin and eyes. It may be toxic.
    CAUTION - RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING
    TO LOCAL REGULATIONS.
    BATTERY REPLACEMENT PROCEDURE:
    1. Turn off and unplug all connected equipment.
    2. Turn the UPS off and unplug it from the AC power source.
    3. Turn the UPS on its side.
    4. Remove the front panel retaining screws located on the bottom of the UPS.
    5. Slide the battery compartment cover (front panel) completely off of the unit.
    6. Remove the batteries from the compartment.
    7. Disconnect the battery wires from the batteries.
    8. CP1350PFCLCD: Install the replacement batteries by connecting the red wire (+) and black wire (-) to the same color connectors from the
    battery pack.
    CP1500PFCLCD: Install the replacement batteries by connecting the wire bundle (composed of one red wire and one black wire) to the
    connector from the battery pack.
    9. Put the batteries back into the compartment.
    10. Slide back the battery compartment cover and tighten the retaining screws.
    11. Recharge the UPS for 8-16 hours to fully charge the battery.
    CP1350PFCLCD
    CP1500PFCLCD
    REMINDER: Batteries are considered HAZARDOUS WASTE and must be disposed of properly. Most retailers that sell lead-acid batteries
    collect used batteries for recycling, as required by local regulations.
    1. ONLINE: The UPS is supplying utility power to connected equipment.
    2. BATTERY: During a severe brownout or blackout, this icon appears and an alarm
    sounds (two short beeps followed by a pause) to indicate the UPS is operating from
    its internal batteries. During a prolonged brownout or blackout, the alarm will beep
    rapidly every 1/2 second (and the BATT.CAPACITY meter shows one 20% capacity
    segment shaded. The capacity depends on how much load added and the runtime
    left.) to indicate the UPS’s batteries are nearly out of power. You should save files
    and turn off your equipment immediately or allow the software to shut the system down.
    3. Energy-Saving: The UPS in energy-saving bypass mode. See “CyberPower
    GreenPower UPS
    TM
    Technology” section for more information.
    4. LOAD capacity / Sensitivity setup: This meter displays the approximate output
    load level (in 20% increments) of the UPS battery outlets. It can also be sensitivity
    setup meter if you are in programming mode. It is to control the sensitivity of the UPS to switch to Battery Mode by selecting UPS shutdown
    voltage range. The higher the sensitivity, the easier the UPS will switch to Battery Mode.
    5. BATTERY capacity: This meter displays the approximate charge level (in 20% increments) of the UPS’s internal battery. During a
    blackout or severe brownout, the UPS switches to battery power, the BATTERY icon appears, and the charge level decreases.
    6. FAULT: This icon appears if there is a problem with the UPS. Press the POWER button to turn off the UPS.
    F01: Battery Mode or Line Mode Overload fault (Turn on the UPS again.)
    F02: Battery Output Short fault (Turn on the UPS again.)
    F03: Charger Fault (Contact CyberPower Systems for support.)
    F04: Internal Fault (Contact CyberPower Systems for support.)
    7. OVER LOAD: This icon appears and an alarm sounds to indicate the battery-supplied outlets are overloaded. To clear the overload,
    unplug some of your equipment from the battery-supplied outlets until the icon turns off and the alarm stops.
    8. SCHEDULE: Users can setup the schedule to turn on and shut down the computer and UPS through PowerPanel
    ®
    Personal Edition
    software. The LCD display will show how much time that the UPS is about to turn on or shut down.
    9. ESTIMATED RUNTIME: This displays the run time estimate of the UPS with current battery capacity and load.
    10. OUTPUT meter: This meter measure, in real time, the AC voltage that the UPS system is providing to the computer, such as normal line
    BASIC OPERATION
    INSTALLING YOUR UPS SYSTEM
    IMPORTANT SAFETY WARNINGS
    DEFINITIONS FOR ILLUMINATED LCD INDICATORS
CyberPower CP1500PFCLCD

Besoin d’aide?

Nombre de questions : 0

Vous avez une question sur le CP1500PFCLCD de la marque CyberPower ou avez-vous besoin d’aide? Posez votre question ici. Fournissez une description claire et complète du problème et de votre question. Plus votre problème et votre question sont détaillés, plus il sera facile pour les autres propriétaires du CP1500PFCLCD de la marque CyberPower de répondre correctement à votre question.

Consultez gratuitement le manuel de la marque CyberPower CP1500PFCLCD ici. Ce manuel appartient à la catégorie Alimentations d'énergie non interruptible et a été évalué par 1 personnes avec une moyenne de 6.9. Ce manuel est disponible dans les langues suivantes: Anglais. Vous avez une question sur le CP1500PFCLCD de la marque CyberPower ou avez-vous besoin d’aide? Posez votre question ici

Spécifications du CP1500PFCLCD de la marque CyberPower

Généralités
Marque CyberPower
Modèle CP1500PFCLCD
Produit Alimentation d'énergie non interruptible
EAN 649532609642, 6495326096426, 999994789056
Langue Anglais
Type de fichier PDF
Caractéristiques
capacité de la puissance de sortie 1500
Puissance de sortie 900
Fréquence d'entrée 60
Estimation de montée subite d'énergie 1030
Bouton de coupure d'urgence d'alimentation (EPO)
Alarmes sonores
Topologie UPS Line-interactive
Autres caractéristiques
Tension nominale à l'entrée 90-140
Tension nominale de sortie 120
Type de batterie 12V/8.5AH
Poids (impérial) 24.7
Dimensions (L x L x H) 3.9 x 14.2 x 10.4 2011-05-04 11:27:54 2012-06-08 13:40:02 8737 17 3 kg 2010-10-11 16:57:50 2012-06-08 13:40:02 8738 18 3 MHz 2010-10-11 16:57:50 2012-06-08 13:40:02 8739 21 3 x 2010-10-11 16:57:50 2012-06-08 13:40:02 8741 23 3 Mbit/s 2010-10-11 16:57:50 2012-06-08 13:40:0
Connectivité
Nombre de prises en sortie 10
Types de sortie AC NEMA 5–15R
Nombre de ports série 1
Ports (RJ11) du modem 1
Nombre de port ethernet LAN (RJ-45) 1
Quantité de Ports USB 2.0 2
Design
Longueur de câble 1.52
Format Tower
Couleur du produit Noir
Certification UL1778, cUL 107.3, FCC DOC Class B
Conformité RoHS
Voyants
Écran LCD
Batterie
Technologie batterie Sealed Lead Acid (VRLA)
Temps de rechargement de la batterie 8
Temps de secours type à demi de charge 11
Temps de secours type au chargement complet 2
Batterie échangeable à chaud
Informations sur l'emballage
Logiciels fournis PowerPanel Personal Edition
Conditions environnementales
Température d'opération 0 - 40
Taux d'humidité de fonctionnement 0 - 90

ModesdEmploi.fr

Vous cherchez un manuel ? ModesdEmploi.fr vous permet de trouver le manuel que vous recherchez en un rien de temps. Notre base de données contient plus d'un million de manuels en PDF pour plus de 10 000 marques. Chaque jour, nous ajoutons les derniers manuels afin que vous trouviez toujours le produit que vous recherchez. C'est très simple : entrez le nom de la marque et le type de produit dans la barre de recherche pour consulter gratuitement et immédiatement le manuel de votre choix en ligne.

ModesdEmploi.fr

© Copyright 2020 ModesdEmploi.fr. Tous droits réservés.

Nous utilisons des cookies pour vous garantir la meilleure expérience sur notre site. Si vous continuez à utiliser ce dernier, nous considérerons que vous acceptez l'utilisation des cookies.

En savoir plus