The unit has surge suppression outlets to provide surge and line noise protection. Three of the surge-only outlets are also ECO controlled
To turn the UPS ON, press the power button for approximately 2 seconds - you will hear a constant tone (1 second) - and release after a
To turn the UPS OFF, press the power button for approximately 2 seconds - you will hear a constant tone (1 second) - and release after two
Alarm setting: The audible alarm can be turned Off or On by quickly pressing the POWER button twice. The default setting is for the Alarm
On. To turn the Alarm Off, quickly press the power button twice. You will hear two short beeps when the Alarm is turned Off. To turn the
Alarm back On, quickly press the power button twice. You will hear a single short beep when the Alarm is turned On. *When the Alarm is
turned Off, there will be no audible notification when the UPS reaches a low battery state.
4.Power On Indicator (green)
This LED is illuminated when the utility power is normal and the UPS outlets are providing power, free of surges and spikes.
5.Mode Switch (EC650LCD and EC850LCD only)
Press the Mode Switch for approximately 3 seconds to enter setup mode to select four functions: Utility High Voltage Range, Utility Low
Voltage Range, ECO ON/OFF, and LCD sleep ON/OFF. When a function is selected, press Mode Switch for 3 seconds to view options.
When an option is selected, wait for 8 seconds for the setting to be confirmed. After the setting has been confirmed the LCD screen will
leave setup mode and go back to status display. If there is no action for 8 seconds during setup, the LCD will also leave setup mode and go
back to the status display.
a.Utility High Voltage Range: Adjust the value of high voltage range.
b.Utility Low Voltage Range: Adjust the value of low voltage range.
c. ECO: Eon/EoF (ON/OFF): Turn on or turn off ECO function. For more information, refer to ECO Function Setup section.
d.LCD: L1/L0 (ON/OFF):
* When LCD is set to L1, LCD will be always ON. When LCD is set to L0, LCD will dim if untouched for 1 minute.
* In battery mode, LCD is always on regardless if the setting is L1 or L0.
ECO Button (EC350G, EC550G, and EC750G only)
Press ECO button for 3 seconds to turn on or turn off ECO function in line mode.
ECO Indicator shows the condition of ECO function. For more information, refer to ECO Function Setup section.
7.Communication Protection Ports
Communication protection ports will protect any standard modem, fax, or telephone line. (RJ11)
Located on the side of the UPS, the circuit breaker serves to provide overload and fault protection.
9.USB Port to PC
The USB port allows connection and communication between the USB port on the computer and the UPS unit. The UPS communicates its
status to the PowerPanel
Personal Edition software. The USB port is also used for operating the UPS in ECO mode. For more information,
refer to ECO Function Setup section.
10.Outlets Designed for AC Adapters
The UPS unit has 4 widely-spaced outlets so AC power adapters can be plugged into the UPS without overlapping or blocking adjacent
ECO FUNCTION SETUP
When the ECO function is active the UPS can detect whether the PC that is connected to the USB port is turned on or off. If the PC is turned
off, the UPS will turn off the ECO controlled outlets and cut power to the devices connected to them in order to save power. Generally, these
are peripherals that are not used when the PC is not turned on.
ECO Controlled Outlets
Three of the surge-only outlets are also ECO controlled outlets. When the PC that is connected to the USB port is turned off, the UPS will
turn off the ECO controlled outlets to save energy.
1.The factory default setting is OFF. ECO mode can only be enabled/disabled and will only be active when the UPS is receiving utility
power and not in battery mode.
2.For the EC650/850LCD, press the Mode switch for approximately 3 seconds to enter setup mode and select the ECO function. When
the ECO function is selected, press the Mode switch for 3 seconds to turn the function ON or OFF. Once ON or OFF is selected, wait 8
seconds for the setting to be confirmed and the LCD screen will return to status mode. For the EC350/550/750G, press the ECO button
for 3 seconds to turn ON or OFF the ECO function.
3.When the ECO function is OFF, utility power from the ECO outlets will always be on. When the ECO function is ON, utility power from
the ECO outlets will turn off if the PC connected to the UPS via the USB port is turned off or if there is no PC is connected to the UPS via
The LED will be blinking when the ECO function is turned ON but the PC is either off or not connected. The LED will be solid if the ECO
function is turned on and the connected PC is on. The LED is off when the ECO function is disabled. See below table for more information.
ECO Outlet Status
With Utility Power
When PC is ON and USB port on the UPS is connected, Peripherals
will receive power to operate.
Without Utility Power
When PC is OFF or the USB port on the UPS is not connected, power
to the Peripherals will be turned off.
Always with Utility
When PC is ON/OFF, Peripherals is always ON.
DEFINITIONS FOR ILLUMINATED LED INDICATORS
every 30 seconds
Utility Failure- The UPS is providing power to battery power-supplied
outlets from its battery.
every 1/2 second
Utility Failure- The UPS is providing battery power. Rapid beeping
indicates the unit will run out of power shortly.
Battery Overload - Occurs when connected equipment exceeds the
listed capacity of the UPS. Turn the UPS off, unplug at least one
piece of equipment from battery outlets, wait 10 seconds, reset the
circuit breaker and turn the unit on.
INPUT voltage meter: This meter measures the AC voltage that the UPS system is receiving from the
utility wall outlet. The UPS is designed to continuously supply connected equipment with stable output
voltage. In the event of a complete power loss, severe brownout, or over-voltage, the UPS relies on its
internal battery to supply consistent 110/120 output voltage. The INPUT voltage meter can be used as
a diagnostic tool to identify poor-quality input power.
OUTPUT voltage meter: This meter measures, in real time, the AC voltage that the UPS system is
providing to the computer during normal AC/Utility Power mode, and battery backup mode.
ESTIMATE RUN TIME: This displays the run time estimate of the UPS with the current battery
capacity and load.
NORMAL icon: This icon appears when the UPS is working under normal conditions.
BATTERY icon: During a severe brownout or blackout, this icon appears and an alarm sounds (two short beeps followed by a pause) to indicate
the UPS is operating from its internal battery. The alarm will continue to sound during a prolonged brownout or blackout. The BATT.CAPACITY
meter will show one 20% capacity segment remaining to indicate the UPS's battery is nearly out of power. You should save files and turn off your
INSTALLING YOUR UPS SYSTEM
IMPORTANT SAFETY WARNINGS
DEFINITIONS FOR ILLUMINATED LCD INDICATORS
The LCD display indicates a variety
of UPS operational conditions. All
descriptions apply when the UPS is
plugged into an AC outlet and turned
on or when the UPS is on battery.
EC650LCD (8 outlets)
EC850LCD (12 outlets)
EC650LCD (8 outlets)
EC350G / EC550G (8 outlets)
EC750G (12 outlets)
Nombre de questions : 0
Vous avez une question sur le EC350G de la marque CyberPower ou avez-vous besoin d’aide? Posez votre question ici. Fournissez une description claire et complète du problème et de votre question. Plus votre problème et votre question sont détaillés, plus il sera facile pour les autres propriétaires du EC350G de la marque CyberPower de répondre correctement à votre question.
À propos de CyberPower EC350G
Consultez gratuitement le manuel de la marque CyberPower EC350G ici. Ce manuel appartient à la catégorie Alimentations d'énergie non interruptible et a été évalué par 1 personnes avec une moyenne de 7.8. Ce manuel est disponible dans les langues suivantes: Anglais. Vous avez une question sur le EC350G de la marque CyberPower ou avez-vous besoin d’aide? Posez votre question ici