Draper Envoy

Draper Envoy mode d'emploi

(1)
  • Copyright © 2013 Draper Inc. Form Envoy_Inst13 Printed in U.S.A.
    Installation/Operating Instructions
    Envoy Electric Projection Screen by Draper
    Hanging Screen
    General:
    When locating viewing surface and checking clearance for screen’s operation,
    remember surface is centered in case. Screen is normally recessed above ceiling
    and may be installed in a varie ty of ways. See typical installation detailed on page
    2. Regardless of mounting method used, the following points apply:
    1 Screen should be lifted into position only by the end mounting brackets.
    Keep case level by lifting end plates simultaneously to prevent surface
    damage. Draper provides eyebolts to use in hoisting the screen. Never
    attempt to lift screen along its length.
    2 Screen should be positively and securely supported so that vibration or even
    abusive pulling on viewing surface will not weaken installation.
    3 Installer must insure that fasteners used are of adequate strength and suitable
    for the mounting surface chosen.
    4 Entire bottom of case must be readily accessible after installation is complete.
    5 Hinge on bottom board and particularly hinge on automatic trap door of screen
    must be permitted to operate freely. Front and back of case must be straight—
    not forced to warp or bow. Hinges must be free from mastic or paint buildup,
    and doors must be unobstructed by ceiling tiles.
    6 Do not use screen case to support adjacent sections of ceiling.
    7 If trim pieces must be attached to case, do not permit screws to pro trude
    through ¾" wall of case. Do not attach trim with nails.
    8 If case is painted, slots around doors should be shielded to protect viewing
    surface from paint splatters or overspray.
    9 Do not seal unit in ceiling unit electrical connections have been made and
    screen has been operated successfully.
    Caution
    1 Read instructions through completely before proceeding.
    2 Follow instructions carefully. Installation contrary to instructions invalidates
    warranty.
    3 Do not lift case in center. Lift the ends simultaneously to avoid damage
    to case and surface.
    4 Before removing screen from crate, check for damage and to make sure
    all parts are included.
    5 Entire bottom of screen case should be unobstructed to permit proper
    operation of automatic trap door, and access to bottom panel for making
    electrical connections or servicing.
    6 Screen should be installed level (using a carpenter’s level).
    7 Nothing should be fastened to screen dowel, viewing surface or auto matic
    trap door.
    8 Operating switch(es) packed separately in screen carton. Do not discard with
    packing material.
    9 Screen operates on 110-120V, 60 hz., 1.1 amp current draw.
    NOTE: Screen has been thoroughly inspected and tested at factory and found
    to be operating properly prior to shipment.
    Electrical Connections
    Screen operates on 110-120V, 60 hz., 1.1 amp current draw.
    Junction box is located just above bottom board near left end of screen. Bottom
    board is held closed with flathead screws and may be opened with a Phillips
    screwdriver. Automatic trap door is held shut by viewing surface and must not be
    forced open. Removal of junction box cover plate exposes red, black and white
    pigtail leads and green internal ground wire per wiring diagram attached.
    Screen is shipped with internal wiring complete and control switch(es) fully boxed.
    Wire connecting screen to switch(es) and switch(es) to power supply should be
    furnished by installer. Connections should be made in accordance with attached
    wiring diagram, and wiring should comply with National and local electrical codes.
    All operating switches should be “off before power is connected.
    Operation
    When screen is first operated, be cautious! If automatic trap door does not drop
    open immediately when switch is flipped “down”, return switch to “off and free trap
    door and/or recheck electrical connections before proceeding. Cycle unit down and
    up several times to confirm satisfactory operation.
    110-120V Single Station Control — 3-position up-off-down switch permits
    operation to be stopped at any point. Factory adjusted limit switches automatically
    stop screen when fully down or fully up.
    110-120V Multiple Station Control—Switches are similar in appearance to
    110-120v Single Station Control. Screen stops when switch is released and
    may be restarted in either direction. Factory adjusted limit switches stop screen
    Limit Adjustments (Standard & Standard Quiet Motors)
    Please Note: Screen limits are factory set for optimum performance of the
    screen. A procedure is outlined below for minor tweaks, but any adjustment
    of these limits may negatively affect the flatness of the screen surface and
    could also void the warranty. Please check with Draper prior to resetting
    screen limits.
    CAUTION: Always be prepared to shut screen off manually when new
    adjustment is being tested. Screen may be severely damaged if viewing
    surface is allowed to run too far up or too far down.
    CAUTION: Be sure all switches are in “off” position before adjusting limit
    switches.
    Tools needed: Flashlight, small flathead screwdriver/Allen wrench (4mm or
    5
    /
    32
    ").
    The motor limit screws are normally located on the audience left of screen roller.
    "DOWN" LIMIT ADJUSTMENT
    To Reduce Screen Drop
    1 Raise screen surface about 1' above desired setting and turn off.
    2 Turn WHITE/DOWN limit screw clockwise (3 screw turns = ½ roller revolution).
    3 Test by running screen down and repeat steps 1 and 2 until desired position is
    reached.
    To Increase Screen Drop
    1 Run screen to the down limit.
    2 With the down switch on, turn the WHITE/DOWN limit screw counterclockwise
    (three turns of screw = ½ roller revolution) to increase drop.
    3 Test by running screen up about 1' and back down to new down limit.
    4 Repeat steps 2 and 3 until desired position is reached.
    "UP" LIMIT ADJUSTMENT
    “Up” limit switch, located immediately above left end of automatic trap door, is
    tripped as door closes. If door does not close fully, limit switch should be raised
    slightly. If door closes too tightly, switch should be lowered slightly.
    Remove steel plate attached to threaded neck of “up” limit switch by removing hex
    nut securing it. Removing plate exposes three Phillips head machine screws which
    hold limit switch bracket in place. Turning these screws clockwise will raise limit
    switch; turning them counterclockwise will lower it.
    Raise switch only in quarter-turn increments. When operating properly automatic
    trap door should close gently and rest against but not press on rubber bumpers
    above it. Adjusting automatic door so that it closes too tightly will damage screen.
    1
    1
    /4"
    1
    1
    /4"
    2
    1
    /4"
    5
    /8"
    2"
    2"
    Ceiling grid and tile
    (by others)
    7
    9
    /16"
    ®
    automatically when fully down or fully up.
    24V Control — Three-button up-stop-down switches stop at any point desired,
    operate in any sequence. Factory adjusted limit switches automatically stop screen
    when fully down or fully up.
    Key Operated Switching — Two kinds of key-operated switches are optionally
    available with this unit. 1 The key-operated power supply switch controls power to
    the screen and switches. When it is “off”, the switches will not operate screen. Key
    may be removed from the switch in either “on” or “off” position. 2 A three-position
    key switch permits the screen to be operated directly by key. In this case, the
    screen’s operator must always have a key.
    RS232/Ethernet—Serial communication and network communication optionally
    available with wall switches, RF or IR remote.
    If you encounter any difficulties installing or servicing your Envoy screen, call your dealer or
    Draper, Inc., Spiceland, Indiana, (765) 987-7999 or fax (765) 987-7142.
    Caution: Do not remove the roller assembly from the case unless
    necessary for repairs. If the roller assembly is removed, be sure motor
    is fully re-seated in the bracket, and re-secure it carefully with the motor
    retaining spring (see diagram below).
    These instructions are meant as a guide only. They do not imply any responsibility
    on the part of the manufacturer for improper installation or faulty workmanship at
    the jobsite.
Draper Envoy

Besoin d’aide?

Nombre de questions : 0

Vous avez une question sur le Envoy de la marque Draper ou avez-vous besoin d’aide? Posez votre question ici. Fournissez une description claire et complète du problème et de votre question. Plus votre problème et votre question sont détaillés, plus il sera facile pour les autres propriétaires du Envoy de la marque Draper de répondre correctement à votre question.

Consultez gratuitement le manuel de la marque Draper Envoy ici. Ce manuel appartient à la catégorie écrans de projection et a été évalué par 1 personnes avec une moyenne de 7.4. Ce manuel est disponible dans les langues suivantes: Anglais. Vous avez une question sur le Envoy de la marque Draper ou avez-vous besoin d’aide? Posez votre question ici

Spécifications du Envoy de la marque Draper

Généralités
Marque Draper
Modèle Envoy
Produit écran de projection
EAN 641092114208
Langue Anglais
Type de fichier PDF
représentation / réalisation
Format d'image 5:4
Largeur de visualisation (l) 305
Hauteur de visualisation (h) 244
Taille d'écran totale (hauteur x largeur) 244 x 305
Diagonale - 2011-05-04 11:27:54 2012-06-08 13:40:02 8737 17 3 kg 2010-10-11 16:57:50 2012-06-08 13:40:02 8738 18 3 MHz 2010-10-11 16:57:50 2012-06-08 13:40:02 8739 21 3 x 2010-10-11 16:57:50 2012-06-08 13:40:02 8741 23 3 Mbit/s 2010-10-11 16:57:50 2012-06-08 13:40:0
Gain de l'écran 2.5
Poids et dimensions
Carter L1 3430
Poids 64000
Hauteur 244
Largeur 305

ModesdEmploi.fr

Vous cherchez un manuel ? ModesdEmploi.fr vous permet de trouver le manuel que vous recherchez en un rien de temps. Notre base de données contient plus d'un million de manuels en PDF pour plus de 10 000 marques. Chaque jour, nous ajoutons les derniers manuels afin que vous trouviez toujours le produit que vous recherchez. C'est très simple : entrez le nom de la marque et le type de produit dans la barre de recherche pour consulter gratuitement et immédiatement le manuel de votre choix en ligne.

ModesdEmploi.fr

© Copyright 2020 ModesdEmploi.fr. Tous droits réservés.

Nous utilisons des cookies pour vous garantir la meilleure expérience sur notre site. Si vous continuez à utiliser ce dernier, nous considérerons que vous acceptez l'utilisation des cookies.

En savoir plus