Draper Rolleramic 240"

Draper Rolleramic 240" mode d'emploi

(1)
  • Copyright © 2013 Draper Inc. Form Rolleramic_Inst13 Printed in U.S.A.
    Wall Installation—
    Brackets should fasten to studding or other structural supports within wall.
    Suspended Installation—
    Chains should be attached to solid beams or rafters above screen. If possible,
    screen mounting brackets should be positioned so chains hang vertically.
    Turnbuckles should be connected between chains and mounting brackets. After
    screen has been suspended, turnbuckles should be adjusted so that screen hangs
    level.
    Recessed Installation—
    Recess should be constructed to fit screen case with brackets (see “Case
    Dimensions” on back page). Design recess so that entire bottom of screen case
    is unobstructed to permit access to bottom panel, screen roller and surface for
    servicing if required.
    Hanging Screen
    General:
    When locating viewing surface and checking clearance for screen operation,
    remember surface is not centered in screen case: see dimensional drawings on
    reverse. All installations should observe these important criteria:
    1
    Screen should be positively and securely supported so that vibration or even
    abusive pulling on viewing surface will not weaken installation.
    2
    Installer must insure that fasteners used are of adequate strength and suitable
    for the mounting surface.
    3
    Entire bottom of case must be readily accessible after installation is complete.
    Be sure the access door opens freely for adjustments and service.
    4
    Installer should make sure mounting brackets are flush with the sides of the
    case to provide stability when hanging screen. Keep case level when lifting
    and mounting.
    5 Screens through 14' wide have 2 mounting brackets; wider screens have 3.
    Brackets should be located along case to line up with supporting beams or
    studding. Motor end bracket must be located 1"-6" to right of access door. Idler
    end bracket must be located 6"-12" from right end of case. Failure to mount
    brackets as directed could cause the case to bow and result in damage to screen.
    Please Note: Mount the case using the two end brackets first. If a center
    bracket is provided, mount it last. The center bracket is designed to prevent
    sagging of the case, and must be mounted so that it is level with the others
    and does not force the screen case up.
    6
    Make sure the top of the screen case's bottom board at no point touches the
    roller/viewing surface.
    7
    Do not use screen case to support adjacent sections of ceiling.
    8
    If trim pieces must be attached to case, do not permit screws to pro trude
    through ¾" wall of case. Do not attach trim with nails.
    9
    If case is painted, viewing surface slot must be shielded to protect viewing
    surface from paint splatters and overspray.
    Do not seal unit in ceiling until electrical connections have been made and
    screen has been operated successfully. Screen must always be installed level
    so that fabric will not roll incorrectly or wrinkle.
    These instructions are meant as a guide only. They do not imply any responsibility
    on the part of Draper, Inc. for improper installation or faulty workmanship at the
    jobsite.
    Installation/Operating Instructions
    Rolleramic Electric Projection Screen by Draper
    Electrical Connections
    Screen operates on 110-120V, 60 hz. AC, .78 amp draw (1.35 with heavy duty
    motor).
    Screens are shipped with internal wiring complete, with all switches (fully boxed)
    and a wiring diagram. Wire connecting screen to switch (or switches) and switch to
    power supply should be supplied by installer. Wires should be connected following
    the wiring diagram provided, and all wiring should comply with local and national
    electrical codes.
    All operating switches should be “Off before power is connected.
    Operation
    Remove all packing before attempting to operate screen. When screen is first
    operated, be cautious! Cycle unit down and up several times to confirm
    satisfactory operation.
    110-120V Single Station Control — 3-position up-off-down switch permits
    operation to be stopped at any point. Factory adjusted limit switches automatically
    stop screen when fully down or fully up.
    110-120V Multiple Station Control — Switches are similar in appearance to 110-
    120V Single Station Control. Screen stops when switch is released and may
    be restarted in either direction. Factory adjusted limit switches stop screen
    automatically when fully down or fully up.
    24V Control — Three-button up-stop-down switches stop at any point desired,
    operate in any sequence. Factory adjusted limit switches automatically stop screen
    when fully down or fully up.
    Key Operated Switching — Two kinds of key-operated switches are optionally
    available with this unit.
    1
    The key-operated power supply switch controls power to the screen and
    switches. When it is “off”, the switches will not operate screen. Key may be
    removed from the switch in either “on” or “off position.
    2
    A three-position key switch permits the screen to be operated directly by key. In
    this case, the screen’s operator must always have a key.
    RS232/Ethernet—Serial communication and network communication optionally
    available with wall switches, RF or IR remote.
    Adjustments
    Please Note: Screen limits are factory set for optimum performance of the
    screen. A procedure is outlined below for minor tweaks, but any adjustment
    of these limits may negatively affect the flatness of the screen surface and
    could also void the warranty. Please check with Draper prior to resetting
    screen limits.
    CAUTION: Always be prepared to shut screen off manually when new
    adjustment is being tested. Screen may be severely damaged if viewing
    surface is allowed to run too far up or too far down.
    CAUTION: Be sure all switches are in “off position before adjusting limit
    switches.
    CAUTION: Do not loosen coupling setscrews from the roller shaft, or the
    screen surface will rapidly unroll and fall. If setscrew must be loosened
    actions should be taken to prevent the roller from turning.
    Adjusting “fully up” position — “Up” limit switch is located on right side of
    limit switch assembly, immediately behind access door to case. Right hand, hex
    head machine screw contacts limit switch button to shut screen off. Turning this
    machine screw clockwise will allow surface to run farther up into case. Turning it
    counterclockwise will cause screen to stop sooner, farther out of the case.
    Adjusting “fully down” position — “Down” limit switch is located on left side of
    limit switch assembly, immediately behind access door to case. Left hand, hex
    head machine screw contacts limit switch button to shut screen off. Turning this
    machine screw clockwise will allow surface to run farther down before stopping.
    Turning it counterclockwise will cause screen to stop in a less extended position.
    At no time should fabric be unrolled far enough to expose any part of screen roller.
    Make all adjustments in small increments, and be sure nut on machine screw is
    tight against steel limit switch support before closing access door.
    ®
    Caution
    1
    Read instructions through completely before proceeding.
    2
    Follow instructions carefully. Installation contrary to instructions invalidates
    warranty.
    3
    Do not lift case in center. Lift the ends simultaneously to avoid damage to
    case and surface.
    4 Entire bottom of screen case should be unobstructed to permit access to
    bottom panels for making electrical connections or servicing. Motor end
    bracket must be located 1"-6" to right of access door. Idler end bracket must
    be located 6"-12" from right end of case. Failure to mount brackets as directed
    could cause the case to bow and result in damage to screen.
    5
    Keep case level when lifting and mounting. Screen should be installed
    level (using a carpenter’s level).
    6
    Nothing should be fastened to screen dowel or viewing surface.
    7
    Do not touch screen while in motion.
    8
    Operating switch (es) packed separately in screen carton. Do not discard
    with packing material.
    9
    Screen operates on 110-120V, 60 hz., .78 amp draw (1.35 with heavy duty motor).
    NOTE: Screen has been thoroughly inspected and tested at factory and found
    to be operating properly prior to shipment.
    Universal Mounting Bracket
    may be suspended from above,
    or mounted to wall. Each bracket
    consists of a front and back piece
    bolted together. 2 required and
    supplied on screens up to 14' wide.
    3 required and supplied on larger screens
    .
    Case
    Conduit connection
    on left end of case.
    Viewing Surface
    If you encounter any difficulties installing or servicing your Rolleramic screen, call your
    dealer or Draper, Inc., Spiceland, Indiana, (765) 987-7999, or fax (765) 987-7142.
    Please Note: The Rolleramic is not available with the TorkStar Utility Line Set.
    Motor end bracket must be located 1"-6" to right of access door. Idler end
    bracket must be located 6"-12" from right end of case. Failure to mount brackets
    as directed could cause the case to bow and result in damage to screen.
Draper Rolleramic 240"

Besoin d’aide?

Nombre de questions : 0

Vous avez une question sur le Rolleramic 240" de la marque Draper ou avez-vous besoin d’aide? Posez votre question ici. Fournissez une description claire et complète du problème et de votre question. Plus votre problème et votre question sont détaillés, plus il sera facile pour les autres propriétaires du Rolleramic 240" de la marque Draper de répondre correctement à votre question.

Consultez gratuitement le manuel de la marque Draper Rolleramic 240" ici. Ce manuel appartient à la catégorie écrans de projection et a été évalué par 1 personnes avec une moyenne de 5.4. Ce manuel est disponible dans les langues suivantes: Anglais. Vous avez une question sur le Rolleramic 240" de la marque Draper ou avez-vous besoin d’aide? Posez votre question ici

Spécifications du Rolleramic 240" de la marque Draper

Généralités
Marque Draper
Modèle Rolleramic 240"
Produit écran de projection
EAN 641092118237
Langue Anglais
Type de fichier PDF
représentation / réalisation
Format d'image -
Hauteur de visualisation (h) 3660
Largeur de visualisation (l) 4880
Diagonale - 2011-05-04 11:27:54 2012-06-08 13:40:02 8737 17 3 kg 2010-10-11 16:57:50 2012-06-08 13:40:02 8738 18 3 MHz 2010-10-11 16:57:50 2012-06-08 13:40:02 8739 21 3 x 2010-10-11 16:57:50 2012-06-08 13:40:02 8741 23 3 Mbit/s 2010-10-11 16:57:50 2012-06-08 13:40:0
Cycle operating par jour (max) Motorized
Taille d'écran totale (hauteur x largeur) 366 x 488
Format Video
Design
Type de montage Ceiling/Wall
Poids et dimensions
Largeur 5640
Hauteur 3660
Poids 109000

ModesdEmploi.fr

Vous cherchez un manuel ? ModesdEmploi.fr vous permet de trouver le manuel que vous recherchez en un rien de temps. Notre base de données contient plus d'un million de manuels en PDF pour plus de 10 000 marques. Chaque jour, nous ajoutons les derniers manuels afin que vous trouviez toujours le produit que vous recherchez. C'est très simple : entrez le nom de la marque et le type de produit dans la barre de recherche pour consulter gratuitement et immédiatement le manuel de votre choix en ligne.

ModesdEmploi.fr

© Copyright 2020 ModesdEmploi.fr. Tous droits réservés.

Nous utilisons des cookies pour vous garantir la meilleure expérience sur notre site. Si vous continuez à utiliser ce dernier, nous considérerons que vous acceptez l'utilisation des cookies.

En savoir plus