EK Water Blocks EK-D5

EK Water Blocks EK-D5 mode d'emploi

(1)
  • Revision 1.0. Released on 12
    th
    of February, 2014.
    Installation and mounting manual for EK-D5 Cover Kit
    This product is intended for installation only by expert users. Please consult with a qualified technician for installation. Improper installation may result in damage to your equipment. EK Water Blocks assumes no liability whatsoever,
    expressed or implied, for the use of these products, nor their installation. The following instructions are subject to change without notice. Please visit our web site at www.ekwb.com for updates. Before installation of this product please
    read important notice, disclosure and warranty conditions printed on the back of the box.
    Before you start using this product please follow these basic guidelines:
    1. Please carefully read the manual before through before beginning with the installation process!
    2. The EK High Flow and EK-CSQ type fittings require only a small amount of force to screw them firmly in place since the liquid seal is ensured by the rubber o-ring gaskets.
    3. The use of corrosion inhibiting coolants is always recommended for any liquid cooling system.
    STEP 1: PREPARING THE PUMP
    SAMPLE INSTALLATION OVERVIEW - EK-D5 X-TOP WITH COVER
    Remove eight (8) original screws marked on
    picture below and remove the original D5 X-
    Top ring. Store original ring for possible reuse
    without D5 Cover.
    Keep original 8 pcs of M4×16mm
    screws as you will need to reuse them!
    STEP 2: UNINSTALLING THE CONNECTOR
    4-PIN MOLEX CONNECTOR
    1. Flatten the pins in Molex connector
    2. Remove Cables from Molex connector
    3-PIN FAN CONNECTOR
    1. Push the pin on fan connector with
    screwdriver
    2. Remove the cable
    STEP 4: INSTALLING THE CONECTOR
    1. Put the screwdriver into pin gap in Molex connector
    2. Recover flattered pin into original position
    3. Put cables back to Molex connector and fan connector(Watch out for correct
    order of cables)
    IMPORTANT DISCLOSURES:
    VERY IMPORTANT NOTICE: Once the installation is completed, it is a recommended practice to test the cooling circuit for leaks prior to powering up the computer. We highly recommend a 24 hour leak test prior to powering up the computer. Do not test the water block
    using tap water pressure. This will rupture the top of the housing and render the block unusable (and will void your warranty).While all efforts have been made to provide the most comprehensive tutorial possible, EK Water Blocks assumes no liability expressed or implied
    for any consequential damage(s) occurring to your equipment as a result of using EK Water Blocks cooling products, either due to errors or omissions on our part in the above instructions, or due to failure or defect in the EK Water Blocks cooling products.
    WARRANTY: Our products are warranted against defects in materials or workmanship for a period of 24 months beginning from the date of delivery to the final user. During this period, products will be repaired or have parts replaced at our discretion provided that: (I) the
    product is returned to the agent from whom it was purchased; (II) the product has been purchased by an end user and has not used for commercial purposes; (III) the product has not been misused, handled carelessly, or used in a manner other than in accordance with
    the instructions provided describing its installation and proper use. This warranty does not confer rights other than those expressly set out above and does not cover any claims for consequential loss or damage. This warranty is offered as an extra benefit and does not
    affect your statutory rights as a consumer. This warranty is voided if the product comes in contact with aggressive UV additives or other improper liquids.
    Any RMA claims are to be solved through our online support ticket system: www.ekwb.com/support.
    REQUIRED TOOLS: Allen Key 2.5mm (Enclosed with Pump top delivedy), Small flat screwdriver or tweezer
    Screws M4x16
    (not enclosed)
    D-5 Pump
    (not enclosed)
    O ring
    (not enclosed)
    EK-D5 X-TOP
    (not enclosed)
    D5 X-TOP RING
    For Cover
    D5 Cover
    ORIGINAL POSITION
    1.Flatter the pins
    pins
    2. Remove cables
    1.Push the pin
    pins
    2. Remove cables
    Watch out for correct order of cables
    2. recover
    the pins
    1. Put the
    screwdriver
    into the gap
    EK badge
    1. Insert cables
    through hole in
    D5 Cover.
    2. Make sure
    that other of D5
    Cover hole is
    over
    potentiometer.
    Sealing gasket (O-ring)
    3. Install new
    X-Top Ring
    4. Tighten screws
    original scews
    D5 X-TOP RING
    5. Place EK badge
    D5 pump
EK Water Blocks EK-D5

Besoin d’aide?

Nombre de questions : 0

Vous avez une question sur le EK-D5 de la marque EK Water Blocks ou avez-vous besoin d’aide? Posez votre question ici. Fournissez une description claire et complète du problème et de votre question. Plus votre problème et votre question sont détaillés, plus il sera facile pour les autres propriétaires du EK-D5 de la marque EK Water Blocks de répondre correctement à votre question.

Consultez gratuitement le manuel de la marque EK Water Blocks EK-D5 ici. Ce manuel appartient à la catégorie Systèmes de refroidissement de matériel informatique et a été évalué par 1 personnes avec une moyenne de 7.9. Ce manuel est disponible dans les langues suivantes: Anglais. Vous avez une question sur le EK-D5 de la marque EK Water Blocks ou avez-vous besoin d’aide? Posez votre question ici

Spécifications du EK-D5 de la marque EK Water Blocks

Généralités
Marque EK Water Blocks
Modèle EK-D5
Produit Système de refroidissement de matériel informatique
EAN 3831109842935
Langue Anglais
Type de fichier PDF
Caractéristiques
Compatibilité EK-D5 X-TOP, EK-D5 Vario X-TOP, EK-D5 X-RES, EK-D5 Vario X-RES, EK-BAY RES D5, EK-BAY RES D5 Vario
Matériel Acétal
Couleur du produit Noir

ModesdEmploi.fr

Vous cherchez un manuel ? ModesdEmploi.fr vous permet de trouver le manuel que vous recherchez en un rien de temps. Notre base de données contient plus d'un million de manuels en PDF pour plus de 10 000 marques. Chaque jour, nous ajoutons les derniers manuels afin que vous trouviez toujours le produit que vous recherchez. C'est très simple : entrez le nom de la marque et le type de produit dans la barre de recherche pour consulter gratuitement et immédiatement le manuel de votre choix en ligne.

ModesdEmploi.fr

© Copyright 2020 ModesdEmploi.fr. Tous droits réservés.

Nous utilisons des cookies pour vous garantir la meilleure expérience sur notre site. Si vous continuez à utiliser ce dernier, nous considérerons que vous acceptez l'utilisation des cookies.

En savoir plus