EK Water Blocks EK-UNI

EK Water Blocks EK-UNI mode d'emploi

(1)
  • All disclosures, notices and warranty conditions are being written on the EKWB website. Please read terms of use. Released on 4
    th
    of Mar, 2014.
    Installation and mounting manual for EK-UNI Holder DDC V2
    This product is intended for installation only by expert users. Please consult with a qualified technician for installation. Improper installation may result in damage to your equipment. EK Water Blocks assumes no liability
    whatsoever, expressed or implied, for the use of these products, nor their installation. The following instructions are subject to change without notice. Please visit our web site at www.ekwb.com for updates. Before installation
    of this product please read important notice, disclosure and warranty conditions printed on the back of the box.
    Before you start using this product please follow these basic guidelines:
    1. Please carefully read the manual before through before beginning with the installation process!
    2. The EK High Flow and EK-CSQ type fittings require only a small amount of force to screw them firmly in place since the liquid seal is ensured by the rubber o-ring gaskets.
    3. The use of corrosion inhibiting coolants is strongly recommended for any liquid cooling system.
    STEP 1: GENERAL INFORMATION:
    STEP 2 PREPARING THE PUMP:
    EK-UNI Holder DDC V2 is only compatible with the Laing DDC pump X-Res/X-Top (see picture below). EK does
    not guarantee compatibility with other brands DDC water pumps or 3rd party pump tops (volutes). Only EK-
    DDC family products are supported! EK-UNI Holder DDC V2 cannot be used with original Laing DDC pump top
    (volute)! Remove four (4) M4x25 DIN 7984 screws with enclosed Allen key like shown on picture below.
    STEP 3: ATTACHING EK-UNI HOLDER
    STEP 4: ATTACHING TO CASE:
    1. Install the DDC pump on X-RES/X-Top per item’s instruction manual.
    2. Place sub assembly on DDC holder so holes are concentric.
    3. Place polyamide washer beneath each M4x30 DIN7985 screws head
    (included).
    4. Screw gently as excessive force may cause screws to strip.
    Use 2 M4x8 ISO7380 screws in conjusction with washers and nuts in order to attach assembly
    to PC case. This holder is meant to be installed directly on the computer chassis. User may
    need to drill 2 (two) Φ4mm holes through chassis metal using electric power drill if there are no
    appropriate mounting holes available.
    IMPORTANT DISCLOSURES:
    VERY IMPORTANT NOTICE: Once the installation is completed, it is a recommended practice to test the cooling circuit for leaks prior to powering up the computer. We recommend
    a 24 hour leak test prior to powering up the computer. Do not test the water block using tap water pressure. This will rupture the top of the housing and render the block unusable
    (and will void your warranty).While all efforts have been made to provide the most comprehensive tutorial possible, EK Water Blocks assumes no liability expressed or implied for
    any consequential damage(s) occurring to your equipment as a result of using EK Water Blocks cooling products, either due to errors or omissions on our part in the above
    instructions, or due to failure or defect in the EK Water Blocks cooling products.
    WARRANTY:Our products are warranted against defects in materials or workmanship for a period of 24 months beginning from the date of delivery to the final user. During this
    period, products will be repaired or have parts replaced at our discretion provided that: (I) the product is returned to the agent from whom it was purchased; (II) the product
    has been purchased by an end user and has not used for commercial purposes; (III) the product has not been misused, handled carelessly, or used in a manner other than in
    accordance with the instructions provided describing its installation and proper use. This warranty does not confer rights other than those expressly set out above and does not
    cover any claims for consequential loss or damage. This warranty is offered as an extra benefit and does not affect your statutory rights as a consumer. This warranty is voided
    if the product comes in contact with aggressive UV additives or other improper liquids.
    Any other RMA issues can be reported to support@ekwaterblocks.com for further analysis.
    REQUIRED TOOLS
    Phillips head screwdriver
    UNI Holder DDC V2
    Mounting mechanism
    M4x25 DIN 7984 screw
    M4x30 DIN7985 screw
    Polyamide washer
    Hole spacing
    M4x8 ISO7380 screw
    M4 metal washer
    M4 nut
    computer chassis
EK Water Blocks EK-UNI

Besoin d’aide?

Nombre de questions : 0

Vous avez une question sur le EK-UNI de la marque EK Water Blocks ou avez-vous besoin d’aide? Posez votre question ici. Fournissez une description claire et complète du problème et de votre question. Plus votre problème et votre question sont détaillés, plus il sera facile pour les autres propriétaires du EK-UNI de la marque EK Water Blocks de répondre correctement à votre question.

Consultez gratuitement le manuel de la marque EK Water Blocks EK-UNI ici. Ce manuel appartient à la catégorie Systèmes de refroidissement de matériel informatique et a été évalué par 1 personnes avec une moyenne de 6.3. Ce manuel est disponible dans les langues suivantes: Anglais. Vous avez une question sur le EK-UNI de la marque EK Water Blocks ou avez-vous besoin d’aide? Posez votre question ici

Spécifications du EK-UNI de la marque EK Water Blocks

Généralités
Marque EK Water Blocks
Modèle EK-UNI
Produit Système de refroidissement de matériel informatique
EAN 3830046997937, 3830046997951
Langue Anglais
Type de fichier PDF
Caractéristiques
Compatibilité X-Res, X-Top
Matériel Acier
Couleur du produit Noir

ModesdEmploi.fr

Vous cherchez un manuel ? ModesdEmploi.fr vous permet de trouver le manuel que vous recherchez en un rien de temps. Notre base de données contient plus d'un million de manuels en PDF pour plus de 10 000 marques. Chaque jour, nous ajoutons les derniers manuels afin que vous trouviez toujours le produit que vous recherchez. C'est très simple : entrez le nom de la marque et le type de produit dans la barre de recherche pour consulter gratuitement et immédiatement le manuel de votre choix en ligne.

ModesdEmploi.fr

© Copyright 2020 ModesdEmploi.fr. Tous droits réservés.

Nous utilisons des cookies pour vous garantir la meilleure expérience sur notre site. Si vous continuez à utiliser ce dernier, nous considérerons que vous acceptez l'utilisation des cookies.

En savoir plus