Fujitsu MAW 3300 NP mode d'emploi

Fujitsu MAW 3300 NP
5.1 · 1
PDF mode d'emploi
 · 2 pages
mode d'emploiFujitsu MAW 3300 NP




Careful handling and installation of your disk drive is paramount to the longevity of the unit. Serious damage can occur to the internal
mechanisms if forces outside the environmental specifications are exerted to the casing. In transportation, always use the original packing
in which the drive was supplied and avoid sharp changes in temperature to minimise the risk of condensation.
1. Never drop. Handle with care.
2. Never move the disk drive while the disks are spinning. This is when the drive is powered on and also immediately after power off.
Refer to the Start/Stop specification for your drive.
3. Always turn off the power before connecting or disconnecting the interface cable. The same applies to changing any of the switches or
terminal settings except Write protect switch on NP model drives.
4. Never place the drive in the vicinity of strong magnetic fields such as monitors, televisions, or loudspeakers.
5. Never use any cleaning agents or liquids on the drive.
6. Always use an antistatic mat and wrist strap when handling the drive. Hold the drive by the Base casting and never touch the components
on printed circuit board.
7. Never remove any labels from the drive and do not deface them in any way; these labels are part of the disk drive design.
8. Never open the disk enclosure for any reason. Doing so voids any warranty.
9. Always pay close attention to the mounting specifications such as sway space and cooling. If the temperature difference between storage
location and installation locations is more than 10°C, leave the drive in the new location for at least two hours for Temperature acclimation.
This minimises any risk of condensation forming on the drive.
The Drive needs NO preventative or periodic maintenance during its life time if properly used in the correct environment.
1. ORIENTATION–The drive can be installed in each six surface down orientations. Inclination from vertical or horizontal should not
exceed 5
2. MOUNTING SCREW INSTALLATION–When the mounting screw holes on the side of the drive are used, be sure to use the two pairs
of outer holes. Do not use the center hole in conjunction with only one of the outer holes. The screws must not penetrate the drive by more
than 5.0 millimeters. Impact caused by the electric driver must be within the device specifications.
3. COOLING–Allow space above and below the drive to provide an adequate air flow. Fan cooling is recommended. The disk enclosure
temperature measured at center of base cover (label side) should never exceed 60°C. See Table 1.
Table 1. Reference value of airflow
Environmental temperature Required velocity of airflow
°C > 0.2m/s
°C > 0.5 m/s
45°C > 0.9 m/s
50°C > 1.5 m/s
4. TERMINATION–A terminator should be installed externally at both ends of the SCSI bus.
5. TERMINATOR POWER–Terminator power must be supplied to terminator for correct operation. This can be supplied from either the
drive, except for NC model or the SCSI bus. If only NC model drives are connected to the SCCI bus, terminator power should be supplied
6. ATTACHING THE CABLES–To avoid possible damage to the drive, make sure the direction of the connector matches.
CAUTION: Warranty may be avoided if damage to the connector is caused by wrong insertion.
Storage Products Group
4-1-1 Kamikodanaka, Nakahara-ku, Kawasaki 211-8588, Kanagawa-ken, Japan
Copyright © 2005 FUJITSU LIMITED


Mode d'emploi

Consultez gratuitement le manuel de la marque Fujitsu MAW 3300 NP ici. Ce manuel appartient à la catégorie Disques durs et a été évalué par 1 personnes avec une moyenne de 5.1. Ce manuel est disponible dans les langues suivantes: Anglais. Vous avez une question sur le MAW 3300 NP de la marque Fujitsu ou avez-vous besoin d’aide? Posez votre question ici

Besoin d’aide?

Vous avez une question sur le Fujitsu MAW 3300 NP et la réponse n'est pas dans le manuel? Posez votre question ici. Fournissez une description claire et complète du problème, et de votre question. Plus votre problème et votre question sont clairement énoncés, plus les autres propriétaires de Fujitsu MAW 3300 NP ont de chances de vous fournir une bonne réponse.

Nombre de questions : 0

Spécifications du MAW 3300 NP de la marque Fujitsu

Vous trouverez ci-dessous les spécifications du produit et les spécifications du manuel du Fujitsu MAW 3300 NP.

Marque Fujitsu
Modèle MAW 3300 NP | CA06550-B460
Produit disque dur
EAN 9016007170128, 0102645871271, 0102645931500
Langue Anglais
Type de fichier Mode d’emploi (PDF)

Foire aux questions

Vous ne trouvez pas la réponse à votre question dans le manuel? Vous trouverez peut-être la réponse à votre question dans la FAQ sur le Fujitsu MAW 3300 NP au dessous de.

Votre question n'est pas dans la liste ? Posez votre question ici

Aucun résultat