KT&C KPC-EW650NU mode d'emploi

KT&C KPC-EW650NU
8.1 · 1
PDF mode d'emploi
 · 2 pages
Anglais
mode d'emploiKT&C KPC-EW650NU
M168-EW650U-001

HIGH PERFORMANCE

CCTV CAMERA

OPERATION MANUAL

Thank you for choosing our high quality camera.
Before attempting to connect or operate, please read and
follow these instructions.

NAME AND FUNCTION

• LENS CONNECTION
Lenses are sold separatele. Lenses such as an auto iris lens,
CS-Mount lens and C-Mount lens can be used.
NOTE
• Please keep the lens clean.
• Any foreign objects and fingermarks on the lens can cause
inferior image quality in low light level conditions.
When using an auto iris lens
1.Please peel off about 8mm of the
outer skin of the auto iris lens cable.
2. Please peel off about 2mm of the
outer skin of the insulated conductor
inside the lens cable.
3. Please remove the cover of the auto iris lens connection plug and solder
the lens cable ti the connector pin in the plug.
*PIN ASSIGNMENT OF THE LENS CONNECTOR
Signal for DC + iris lens
Pin 1: DAMP-
Pin 2: DAMP+
Pin 3: DRV+
Pin 4: DRV-(GND)
Signal for Video + iris lens
Pin 1: Power source: +9 DC,50mA MAX
Pin 2: N.C(Not used)
Pin 3: Video Signal:0.7Vp-p/10K ohms.
Pin 4: Shield, ground
4. Please replace the auto iris lens connection plug cover and take off the
CCD protection cap and than attach the auto iris lens to the camera by
screwing it in clockwise.
Back Focus Procedure
Step 1 - Remove Lens Cover.
Step 2 - If using a C-Mount lenses it can be applied
to the camera at this time.
Step 3 - Most current lenses are CS-Mount and
require removal of the C/CS ring.
Step 4 - To remove the C/CS ring loosen but do not
remove completely the two set screws and
than remove the C/CS ring.
Step 5 - Screw on the CS-Mount lens until a good
picture is obtained and tighten the set screws.
Step 6 - Use the focus ring on the lens to obtain
a finer focusing
NOTE
- if a C-Mount lens was applied and focus could not be obtained, please try the following :
• Ensure that the lens is in face a C-Mount and not a CS-Mount.
•Check the focus adjust on the lens.
• if need be loosen the set screws and adjust the position of the lens
and C/CS ring as one unit until a good focus is obtained.
5. Please insert the connection plug that is connected to the auto iris lens cable into the
auto lens connector, which is located on the back of the camera
* As the connecting method varies with instruments, refer to the
manual supplied with the instrument.
* Only connect the cable when the power is turned off.
* Set the 75Ω / Hi-Z selection switch as shown below if you have an intermediate device.
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following
two conditions;
1. This device may not cause harmful interference.
2. This device must accept any interference received, including
interference that may cause undesired operation.
Any changes or modications in construction of this devies which are not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Caution -
CAUTION
1. A regulated DC12V 300mA power supply is recommended for use with this camera for the best picture and the most stable operation. An unregulated power supply can cause damage to the camera.When unregulated power supply is applied, product warranty will beout of subject.2. It is recommended that the camera is used with a monitor that has a CCTV quality 75 video impedance level. If your monitor is switched to high impedance then please adjust accordingly.3. Do not attempt to disassemble the camera to gain access to the internal componets. Refer servicing to your dealer.4. Never face the camera towards the sun or any bright or reective light, which may cause smear on the picture and possible damage to the CCD.5. Do not remove the serial sticker for the warranty service.This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.”
Note -
This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.
WARNING -

CAUTIONS CAUTIONS

Correct Disposal of This Product
(Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European
countries with separate collection systems)
This marking shown on the product or its literature, indicate that
it should not be disposed with other household wastes at the end
of its working life. To prevent possible harm to the environment or
human health from uncontrolled waste disposal, please separate
this from other types of wastes and recycle it responsibly to
promote the sustainable reuse of material resources.
This product should not be mixed with other commercial wastes
purchased this product, or their local government ofce, for details
of where and how they can take item for environmentally safe
recycling.
Business users should contact their supplier and check the terms
and conditions of the purchase contract.
Household users should contact either the retailer where they for
disposal.
CAUTION
RISK OF ELECTRIC SHOCK DO NOT OPEN
CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO
NOT REMOVE COVER(OR BACK). NO USER. SERVICING TO
QUALIFED SERVICE PERSONNEL.
This symbol is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufcient mangnitude to constitute a risk of electric shock to persons.This symbol is intended to alert the user to the presence of important operating and maintenance(servicing) instruction in the literature accompanying the appliance.

COMPONENTS

FRONT
BACK
CS-Mount
C-Mount
Lens Cover
Lens Cover
C/CS RING

INSTALLATION

• MONITOR CONNECTION
BNC FEMALE
VIDEO
DC12V REGULATED
POWER SUPPLY
VIDEO IN
. MENU BUTTONUP BUTTONDOWON BUTTONLEFT BUTTONRIGHT BUTTON. Auto IRIS Jack
CS-MOUNT ADAPTOR RING
Set Screw(Left Side)
AUTO
IRIS
OSD
CONTROL
High Performance
DSP Color Camera
Auto Iris Lens
Connection Plug
C-mount Adaptor Ring
Spare Screw (Machine 2x2) - 2ea
Operation Manual

Mode d'emploi

Consultez gratuitement le manuel de la marque KT&C KPC-EW650NU ici. Ce manuel appartient à la catégorie Caméras de surveillance et a été évalué par 1 personnes avec une moyenne de 8.1. Ce manuel est disponible dans les langues suivantes: Anglais. Vous avez une question sur le KPC-EW650NU de la marque KT&C ou avez-vous besoin d’aide? Posez votre question ici

Besoin d’aide?

Vous avez une question sur le KT&C KPC-EW650NU et la réponse n'est pas dans le manuel? Posez votre question ici. Fournissez une description claire et complète du problème, et de votre question. Plus votre problème et votre question sont clairement énoncés, plus les autres propriétaires de KT&C KPC-EW650NU ont de chances de vous fournir une bonne réponse.

Nombre de questions : 0

Spécifications du KPC-EW650NU de la marque KT&C

Vous trouverez ci-dessous les spécifications du produit et les spécifications du manuel du KT&C KPC-EW650NU.

Généralités
Marque KT&C
Modèle KPC-EW650NU
Produit caméra de surveillance
Langue Anglais
Type de fichier Mode d’emploi (PDF)
représentation / réalisation
Type Caméra de sécurité CCTV
Installation prise en charge Intérieure et extérieure
Technologie de connectivité Avec fil
Certification CE, FCC
mode Jour/Nuit Oui
Large dynamique éventaille (WRD) Oui
Langues prises en compte ARA,CHI (SIMPL),CHI (TR),DEU,ENG,ESP,FRE,HIN,JPN,POR,RUS,TUR
Nombre de langues 13
Design
Type de montage -
Format Boîte
Couleur du produit Noir
Détails techniques
Iris Oui
Monture d'objectif d'interface C mount,CS mount
Sortie Vidéo 1
Niveau de sortie maximum 1 Vpp
Impédance de sortie 75 Ohm
Contenu de l'emballage
Vis incluses Oui
Manuel d'utilisation Oui
nombre de caméras 1
Puissance
Connexion Ethernet, supportant l'alimentation via ce port (PoE) Non
Sortie CC en volts 12
Consommation électrique 150 mA
Vidéo
Système de format du signal analogique NTSC
Full HD Non
nombre de lignes TV 750
Résolution maximale 1020 x 508 pixels
Réduction du bruit Oui
Contrôle automatique du gain Oui
Masquage des données personnelles Oui
Défilement et miroir Oui
Ajustement de la qualité d'image Contrast,Sharpness
Détecteur d'image
Type de capteur HAD CCD II
Taille du capteur optique 1/3 "
Audio
Rapport signal-sur-bruit 50 dB
Caméra
Illumination minimum 0.000001 lux
Vitesse d'obturation de l'appareil photo 1/60 - 1/100000 s
Balance des blancs ATW,Manual,Push
Système d'objectif
Nombre maximum d'ouverture 1.4
Capacité du zoom Oui
Zoom numérique 3 x
vision de nuit
Vision nocturne -
Sécurité
Détecteur de mouvement Oui
Conditions environnementales
Température d'opération -10 - 50 °C
Température hors fonctionnement -20 - 60 °C
Humidité relative de fonctionnement (H-H) 0 - 80 %
Poids et dimensions
Largeur 30.5 mm
Profondeur 55 mm
Hauteur 30.5 mm
Poids 113 g
Support de stockage
Disque dur intégré -
Réseau
Ethernet/LAN Non
Wifi Non
voir plus

Foire aux questions

Vous ne trouvez pas la réponse à votre question dans le manuel? Vous trouverez peut-être la réponse à votre question dans la FAQ sur le KT&C KPC-EW650NU au dessous de.

Votre question n'est pas dans la liste ? Posez votre question ici

Aucun résultat