Remove the Front Panel
Press button in the upper left corner
, and then the front panel will be folded down.
AUX IN jack
Do not attempt to modify the unit, modifying the unit may cause an accident.
or servicing of the unit by persons without training and experience in
ronic equip ment a nd aut omoti ve acce ssori es may be dan gerou s and co uld
expose you to the risk of electric shock or other hazards.
the ve hicle befor e carrying o ut any oper ation that c ould interf ere with you r
Keep the volume at a level which you could hear sounds from outside the vehicle.
not work in extremely high or low temperature. Be sure the temperature inside
the vehicle is between +60°C and -10°C before turning on your unit.
replacing the fuse(s), the replacement must be of the same amperage as
shown on the fuse holder
not block vents or radiator panels. Blocking them will cause heat to build up
inside and may result in re.
Using this unit without running the engine can result in battery drainage.
Use only in cars with a 12 volt negative ground.
completing the installation and beginning to play the unit(including replacing
battery), please remove the front panel at rst, and then press RESET button
base with pointed object (such as ball-point pen) to set the unit to initial sta-
you install the unit, remove absolutely the two transportation screws on top
of the unit.
GB - 1
CAR RADIO CD/MP3
YER WITH USB & SD
Please read the instruction carefully
before operating the unit.
* Do not attempt to load more than one disc.
* Only 12cm discs are compatible.
New discs may have some roughness around the edges. Before load such disc into
player, use a ball-point pen or the like to remove any roughness from the edge of
* If there is a scratch,
dirt or ngerprints on the disc, it may cause tracking error. Before
playing, clean the disc with a clean cloth. Wipe the disc from the center out.
store discs in places with high temperatures or high humidity , they can become
After playing, store the disc in its case.
GB - 2
GB - 3
2. Line out Right (red)
3. Line out Left (white)
4. Output plug (male)
5. Output plug (female)
6. FUSE holder (15
Make sure to connect the color coded leads according to the diagram. Incorrect con-
nections may cause the unit to malfunction or damage the vehicle’s electrical system.
- Make sure to connect
the speaker (-) leads to the speaker (-) terminal. Never connect
the left and right channel speaker cables each other or to the vehicle body
- Make sure all the connections are completely correct before turning on your unit.
not connect the ignition wire (red) and the battery wire (yellow), it may cause a short circuit,
even result in re.
1. Remove the outer trim frame.
2. Select a position where the screw holes of the mounting bracket supplied with the
car and the screw holes of the main unit become aligned (are tted).
ighten the screws. And then fasten them to the car .
GB - 4
GB - 5
Install the front panel
Insert the panel into the housing and make sure the panel is properly installed.
Otherwise, abnormality occurs on the display or some keys will not function properly
Never put any objects into the front panel.
Remove the unit
1. Detach the front panel. (please refer to upper part)
ake out the outer trim frame.
3. Insert the keys
supplied to the unit at the both sides of the unit (shown as illustrated)
they click. Pulling the keys and makes them to remove the unit from the dash-
GB - 6
T IO N OF CO NTROL S
GB - 7
Notice on disc
Use such discs may cause malfunction or breakdown of the internal mechanism:
large scratches; with irregular shape; cracked; with any cellophane tape or other
glue on it or with peeling off marks; with protection
sheet; equipped with stabilizers, etc.
- Method 2 DIN Rear-mount (For Japanese car)
C OPER A TIO N
urning on/off the unit
PWR button to turn on the unit. Press this button again to turn off the unit.
Note: When the unit is off, press any key except to turn on the unit.
Selecting the mode
After the unit is on, press
7/MOD button to select different sourcing mode: Radio
CD USB SD/MMC
CK YOUR UNI T
When you unpack your new
car radio, make sure that you have removed all the acces-
sories and information papers:
Install the unit
- Method 1: DIN Front-Mount
T ALL AND R EM OVE TH E UNI T
D FE A TURES
Setting the Sound:
press SEL/VOL knob to select the desired mode in the following order :
(Bass) -> “TRE” (Treble) -> “BAL” (Balance) -> “F AD“ (Fader) ->“BEEP“ (BEEP
-> “T A VOL“ (T A volume) ->”LOC” (local) ->”STEREO” -> “EON” (EON ON/
-> “VOL” (Volume). After selecting the desired mode, you can adjust the current
level by rotating the
SEL/ VOL knob.
BEEP: In Beep mode, rotate SEL/VOL- to select “BEEP ON” or “BEEP OFF”, for cor
responding BEEP status.
EON: please refer to RDS operation.
Note: The unit will return to the previous mode after 5 seconds without key press.
Reset the unit
the unit for the rst time or after replacing the car battery , you must reset
unit. T o set the unit to initial status, press RESET button located on the base with
pointed object. When some errors occur in display , you can also reset the unit, but it
will erase the clock setting and some memorized functions.
o i nc re as e o r de cr ea se t he so un d le ve l, r ot at e SE L/ VO L kn ob cl oc kw is e or a nt i-
are listening to pop music, classic music or rock music, use the equalizer to
adjust the sound quality
. Repeatedly press EQ button to select different equalizer mode
in following order: FLA
T ->POP->ROCK->CLASS -> EQ off.
Switching Loudness On/off
ss and h old BAND/ LOU D butt on u nti l “LOU D ON” sho ws on dis pla y to acti vat e
function. By this function, you can increase the low frequency , which can
improve sound sensitivity
. Press and hold this button again until “LOUD OFF” to cancel
It will return to normal play mode if no key is pressed within 5 seconds.
- In case a RDS station is received.
In radio mode: CT -> FREQ ->PTY
In CD (MP3 / WMA) mode: CD (MP3/WMA) -> CT -> FREQ -> PTY
- In case received station is not RDS.
In radio mode: CT -> FREQ -> NO PTY
-> NO PS
In CD mode: CD -> CT -> FREQ -> NO PTY
-> NO PS
0/DSP button to show the current time on display .
Adjust time: Long press
0/DSP until clock time with ashing hour digits appears.
Then Press and button to adjust the hour value and press
0/DSP to conrm.
Then minute digits ash. Press and button to adjust the minute value and
0/DSP to conrm.
G R EE N /B L AC K)
V IO LE T / B L AC K )
H IT E /B L AC K)
I OL E T)
G R AY )
H IT E )
G R AY / BL A CK )
G R EE N )
4 2 8
3 1 7
4 2 8
3 1 7
+12V Accessory/Switch (Red
Power Antenna/Amplifier Turn on (Blue)
+12V Constant Power Supply (Yellow)
E hol der (1 5 A)
2 3 5 6
AR-3108 IB MUSE 001 REV0 GB.indd1 1