Panasonic WV-SPV781 mode d'emploi

Panasonic WV-SPV781
(1)
  • N. d. pages: 2
  • Type de fichier: PDF
● Switches the MONITOR OUT terminal output between NTSC and PAL.
Included Installation Instructions
PGQX1821YA Cs0615-1075 Printed in China
Two-dimensional
matrix barcode
(Data Matrix):
To our website
*2
IMPORTANT:
Also waterproof the
F
2P power cable (accessory),
E
4P alarm cable (accessory), and external connec-
tions in the same way.
Stretch the tape to approx. twice its length (see the
illustration) and wind it around the cable. Insufficient
tape stretch causes insufficient waterproofing.
To prevent the LAN cable hook from coming loose
easily, fit the
D
LAN connector cover (accessory)
onto the pigtail cable as illustrated, and then slide it in
the direction indicated by the arrow. The connector of
the LAN cable used with this camera must meet the
following restrictions.
Height when inserted (From bottom to hook.):
Max. 16 mm {5/8 inches}
Connector width: Max. 14 mm {9/16 inches}
To install this product outdoors, be sure to waterproof
the cables.
Waterproof grade (IEC IP66 or equivalent) is applied
to this product only when it is installed correctly as
described in these operating instructions and appro-
priate waterproof treatment is applied.
The camera mount bracket is not waterproof.

Installation Guide

Network Camera

Model No. WV-SPV781L
This manual describes the installation procedures, network camera installation, cable
connections, and eld-of-view adjustment.
Before reading this manual, be sure to read the Important Information.

Major operating controls

The component names of the camera are as follows. Refer to the illustration when
installing or adjusting the camera.

Standard accessories Making connections

Important Information ............................... 1 pc.
Warranty card ........................................... 1 set
Code label
*2
.............................................. 1 pc.
Installation Guide (this document) ............ 1 set
CD-ROM
*1
................................................. 1 pc.
Camera caution label................................ 1 pc.
*1
The CD-ROM contains the operating instructions and different kinds of tool software programs.
*2 This label may be required for network management. The network administrator shall retain
the code label.
*3 The audio/monitor output cable can be switched to be used as MONITOR OUT using the
software. The MONITOR OUT conversion plug is used to connect the camera to the audio/
monitor output cable and to convert a stereo mini jack (ø3.5 mm) {1/8 inches} into an RCA pin
output jack.
A Camera mount bracket cover ........... 2 pcs.
B Camera mount bracket cover fixing screw
(M3 x 6 mm {1/4 inches}) ................... 3 pcs.
(incl. 1 spare)
C Waterproof tape .................................. 1 pc.
D LAN connector cover ........................... 1 pc.
E 4P alarm cable .................................... 1 pc.
F 2P power cable .................................... 1 pc.
G MONITOR OUT conversion plug
*3
....... 1 pc.
H Safety wire .......................................... 1 pc.
I Wire lug fixing screw
M3 x 10 mm {3/8 inches} .................... 2 pcs.
(incl. 1 spare)
J Safety wire lug ..................................... 1 pc.
K Protection cover ................................... 1 pc.
L Adapter box .......................................... 1 pc.
M Mounting screws for adapter box (M5 × 20
mm {13/16 inches}) ............................. 5 pcs.
(of them, 1 for spare)
N Adapter box mounting screw
(M4 × 35 mm {1- 3/8 inches}) ............... 1 pc.
● How to initialize the camera
Follow the steps below to initialize the network camera.
1 Turn off the power of the camera. When using a PoE hub, disconnect the LAN cable from the camera.
When using an external power supply, disconnect the 2P power cable plug from the camera.
2
Turn on the power of the camera while holding down the INITIAL SET button, and then keep holding
down the button for 5 seconds or more. About 2 minutes after you have released the INITIAL SET but
-
ton, the camera will start up and the settings including the network settings will be initialized.
When data is being sent via the network camera Blinks green (accessing)
Turn off each system’s power supply before making a connection. Before making connections,
prepare the required peripheral devices and cables.
When the camera is able to communicate with the Lights orange
connected device
When an SD memory card is inserted and could Lights off → Blinks green →
be recognized Lights off
When data can be saved after the SD memory card is inserted Lights off → Lights green
and the SD ON/OFF button is pressed (for less than 1 second)
When data can be saved to the SD memory card Lights green
When the SD memory card is removed after holding down
Lights green → Blinks green →
the SD ON/OFF button for about 2 seconds Lights off (recording)
Lights green →
Lights off (waiting for recording)
When data cannot be saved to the SD memory card because Lights off
an abnormality was detected or the SD memory card is
configured not to be used
When AF (Auto Focus) operation is being executed
Blinks red (about once per second)
When the camera is being started Lights red
When an SD memory card is recognized normally
Lights red → Lights off
When the SD memory card slot is not used or an abnormality Lights red → Stays red
is detected in SD memory card after the camera has started
IMPORTANT:
When the camera is initialized, the settings including the network settings will be initialized.
Note that the CRT key (SSL encryption key) used for the HTTPS protocol will not be initialized.
Before initializing the settings, it is recommended to write down the settings in advance.
Do not turn off the power of the camera during the process of initialization. Otherwise, it may
fail to initialize and may cause malfunction.
IMPORTANT:
Use all 4 pairs (8 pins) of the LAN cable (category 5 or better, straight).
The maximum cable length is 100 m {328 feet}.
Make sure that the PoE device in use is compliant with IEEE802.3af standard.
When connecting both the 12 V DC power supply and the PoE device for power sup-
ply, 12 V DC will be used for power supply
*
.
* If a 12 V DC power supply and a PoE hub or router are used at the same time, net-
work connections may not be possible. In this case, disable the PoE settings. Refer
to the operating instructions of the PoE hub or router in use.
* Depending on the PoE device used, if you stop the 12 V DC power supply after
operating it and a PoE hub or router at the same time, the power supply may stop,
causing the camera to restart.
When the LAN cable is disconnected once, reconnect the cable after around 2 sec-
onds. When the cable is quickly reconnected, the power may not be supplied from
the PoE device.
When cables are used outdoors, there is a chance that they may be affected by light-
ning. In this case, install a lightning arrester just before where the LAN cable con-
nects to the camera.
Connect a LAN cable (category 5 or better, straight)
Waterproof treatment for the cable joint sections
When connecting to a network using a PoE hub
Microphone/line input cable
Connect a stereo mini plug (ø3.5 mm {1/8 inches}).
Input impedance: Approx. 2 kΩ (unbalanced)
Recommended cable length: Less than 1 m {3.28 feet} (for microphone input) Less than
10 m {32.8 feet} (for line input)
Recommended microphone: Plug-in power type (option)
• Supply voltage: 2.5 V ±0.5 V
• Recommended sensitivity of microphone: -48 dB ±3 dB (0 dB=1 V/Pa,1 kHz)
Input level for line input: Approx. -10 dBV
* Use an external powered speaker.
Connect an external amplifier-embedded speaker to the audio/
monitor output cable
Connect a stereo mini plug (ø3.5 mm {1/8 inches}).
*
Output impedance: Approx. 600 Ω (unbalanced)
Recommended cable length: Less than 10 m {32.8 feet}
Output level: -20 dBV (can switch to monitor output)
IMPORTANT:
Connect/disconnect the audio cables and turn on the power of the camera after turn-
ing off the power of the audio output devices. Otherwise, loud noise may be heard
from the speaker.
Make sure that the stereo mini plug is connected to this cable. When a monaural mini
plug is connected, audio may not be heard. When connecting a monaural speaker
with amplifier, use a locally procured conversion cable (mono-stereo).
Adequate waterproof treatment is required for the cables when installing the camera with cables
exposed or installing it under the eaves.
The camera body is waterproof, but the cable ends are not waterproof. Be sure to use the sup-
plied waterproof tape at the points where the cables are connected to apply waterproof treatment
in the following procedure.
Failure to observe this or use of a tape other than the provided waterproof tape (such as a vinyl
tape) may cause water leakage resulting in malfunction.
Before starting the installation, check the entire system conguration.
The following illustration gives a wiring example of how to connect the camera to the network via
a PoE device (hub).
<LAN cable> < Alarm input/output cable, power cable, micro-
phone/line input cable, audio/monitor output
cable>
Stretch the tape to
approx. twice its length.
2 x
IMPORTANT:
The adjustment monitor is used to adjust the field of view when installing or servicing
the camera. It is not provided for recording/monitoring use.
Depending on the adjustment monitor, some characters (camera title, preset ID, etc.)
may not be displayed on the screen.
Use a switching hub or a router which is compliant with 10BASE-T/100BASE-TX.
If a PoE hub is not used, each network camera must be connected to a 12 V DC
power supply.
When using 12 V DC, power supply from a PoE hub or router is not required.
The hook engages
with the connector
terminal
D LAN connector cover
(accessory)
Sunshield
TILT lock screw
Camera
Arm
K
Protection
cover (installed)
Front cover
Camera
Yawing
lock screw
H
Safety wire
(accessory)
PAN lock screws
(2 pcs: The other is on the
opposite side)
L
Adapter
box
(accessory)
A
Camera mount
bracket covers
(2 pcs.) (accessory)
Camera
mount bracket
*1 SDXC/SDHC/SD memory card is described as SD memory card.
*2 Depending on the scanning application used, the Data Matrix may not be
able to be read correctly. In this case, access the site by directly entering the
following URL.
http://security.panasonic.com/pss/security/support/qr_sp_select.html
Connect the power cable
IMPORTANT:
Use 12 V DC power supply that is insulated from the commercial AC power.
Be sure to use the
F
2P power cable (accessory) provided with this product.
Be sure to fully insert the
F
2P power cable (accessory) into the 12 V DC power sup-
ply terminal. Otherwise, it may damage the camera or cause malfunction.
When installing the camera, make sure that excessive force is not applied to the
power cable.
Be sure to use an AC adaptor compliant with the specifications (written in the indication
label on the bottom side of this unit) regarding power source and power consumption.
Power cable
12 V DC
Red Positive
Black Negative
<Required cable>
LAN cable (category 5 or better, straight)
Use a LAN cable (category 5 or better, cross) when directly connecting the camera to a PC.
Note:
Off, input, and output of the external I/O terminal 2 and 3 can be switched by configur-
ing the setting. Refer to the Operating Instructions on the provided CD-ROM for further
information about the external I/O terminal 2 and 3 (ALARM IN2, 3) settings (“Off”,
“Alarm input”, “Alarm output”, “AUX output” or “DAY/NIGHT switching output”).
IMPORTANT:
Be sure to use the
E
4P alarm cable (accessory) provided with this product.
Install external devices so that they do not exceed the ratings above.
When using the external I/O terminals as the output terminals, ensure they do not
cause signal collision with external signals.
Connect the alarm input/output cable
<Ratings>
ALARM IN1 (
DAY/NIGHT IN
), ALARM IN2, ALARM IN3
Input specification: No-voltage make contact input (4 V - 5 V DC, internally pulled up)
OFF: Open or 4 V - 5 V DC
ON: Make contact with GND (required drive current: 1 mA or more)
ALARM OUT, AUX OUT (DAY/NIGHT OUT)
Output specification: Open collector output (maximum applied voltage: 20 V DC)
Open: 4 V - 5 V DC by internal pull-up
Close: Output voltage 1 V DC or less (maximum drive current: 50 mA)
* The default of EXT I/O terminals is “Off”.
E
4P alarm cable (accessory)
PoE device (hub)
PC
Adjustment monitor
LAN cable
(category 5 or better, straight)
Microphone
Powered
speaker
Analog monitor
PC
SD memory card
slot
1 When the SD ON/OFF button is pressed for less than 1 second, the SD MOUNT indicator is lit green
and data can be saved to the SD memory card
*1
.
2 When the SD ON/OFF button is held down for about 2 seconds, the SD MOUNT indicator goes out,
and the SD memory card can be removed.
For U.S. and Canada:
Panasonic System Communications
Company of North America,
Unit of Panasonic Corporation
of North America
www.panasonic.com/business/
For customer support, call 1.800.528.6747
Two Riverfront Plaza, Newark, NJ 07102-5490
Panasonic Canada Inc.
5770 Ambler Drive, Mississauga,
Ontario, L4W 2T3 Canada
(905)624-5010
www.panasonic.ca
For Europe and other countries:
Panasonic Corporation
http://www.panasonic.com
Panasonic System Networks Co., Ltd.
Fukuoka, Japan
Authorised Representative in EU:
Panasonic Testing Centre
Panasonic Marketing Europe GmbH
Winsbergring 15, 22525 Hamburg, Germany
The following parts are used during installation procedures.
GND (black)
ALARM IN3, AUX OUT, DAY/NIGHT OUT (gray)
(Alarm input 3, AUX output, DAY/NIGHT switching output)
ALARM IN2, ALARM OUT (red) (Alarm input 2, Alarm output)
ALARM IN1, DAY/NIGHT IN (green) (Alarm input 1/ DAY/NIGHT switching input)
RJ45 (female)
Network cable
LAN cable
(category 5 or better, straight)
E
4P alarm cable
(accessory)
Alarm input/output cable
(External I/O terminal)
Power cable
(12 V DC)
F
2P alarm cable
(accessory)
Microphone/line input cable (white)
Audio/monitor output cable (black)
Caution:
A READILY ACCESSIBLE DISCONNECT DEVICE SHALL
BE INCORPORATED TO THE EQUIPMENT POWERED
BY 12 V DC POWER SUPPLY.
ONLY CONNECT 12 V DC CLASS 2 POWER SUPPLY (UL
1310/CSA 223) or LIMITED POWER SOURCE (IEC/EN/
UL/CSA 60950-1).
Wind the tape in a
half-overlapping manner.
Wind the tape in a
half-overlapping
manner.
© Panasonic System Networks Co., Ltd. 2015
12 V DC
(red)
GND
(black)
Note:
Use a thin, non-conductive tool to press the switch.
C
Waterproof tape (accessory)
C
Waterproof tape (accessory)
Connect the output cable of the AC adaptor to the
F
2P power cable (accessory).
Side B (Upper)
Side A (lower)
Rating label
Dehumidifying
device
MONITOR OUT jack
(Video Out terminal
Default:
For NTSC monitor)
NTSC/PAL switch
INITIAL SET button
SD ON/OFF button
SD MOUNT indicator
SD ERROR/AF indicator
ACT indicator
LINK indicator
AF (Auto Focus)
button
TELE button
(The camera zooms in.)
WIDE button
(The camera zooms out.)
Panasonic WV-SPV781

Besoin d’aide?

Nombre de questions : 0

Vous avez une question sur le WV-SPV781 de la marque Panasonic ou avez-vous besoin d’aide? Posez votre question ici. Fournissez une description claire et complète du problème et de votre question. Plus votre problème et votre question sont détaillés, plus il sera facile pour les autres propriétaires du WV-SPV781 de la marque Panasonic de répondre correctement à votre question.

Consultez gratuitement le manuel de la marque Panasonic WV-SPV781 ici. Ce manuel appartient à la catégorie Caméras de surveillance et a été évalué par 1 personnes avec une moyenne de 7.5. Ce manuel est disponible dans les langues suivantes: Anglais. Vous avez une question sur le WV-SPV781 de la marque Panasonic ou avez-vous besoin d’aide? Posez votre question ici

Spécifications du WV-SPV781 de la marque Panasonic

Généralités
Marque Panasonic
Modèle WV-SPV781
Produit caméra de surveillance
EAN 0779184178439, 0885170251984, 4010869208789
Langue Anglais
Type de fichier PDF

Foire aux questions

Ci-dessous, vous trouverez les questions les plus fréquemment posées à propos de Panasonic WV-SPV781.

Votre question n'est pas dans la liste ? Posez votre question ici