Roland XI-MADI mode d'emploi

Roland XI-MADI
7.5 · 1
PDF mode d'emploi
 · 2 pages
Anglais
mode d'emploiRoland XI-MADI
Before using this unit, carefully read “USING THE UNIT SAFELY” and “IMPORTANT NOTES”
on back side. After reading, keep the document(s) including those sections where it will be
available for immediate reference.
* 5 1 0 0 0 4 4 9 3 1 - 0 1 *

Installing the Expansion interface

Install the expansion interface on a compatible device.
Important Notes on Handling
To avoid the risk of damage to internal components that can be caused by static electricity,
please carefully observe the following whenever you handle the expansion interface.
• Before you touch the expansion interface, always rst grasp a metal object (such as a
water pipe), so you are sure that any static electricity you might have been carrying
has been discharged.
• When handling the expansion interface, grasp it only by the panel or the expansion
interface’s edges. Avoid touching any of the electronic components or connectors.
• Before you connect any cables, make sure they do not carry a static electricity charge.
Such charges can be transmitted, for example, if the other end of the cable has been
in contact with a carpet (or other object) where there is a static electricity buildup.
• Save the bag in which the expansion interface was originally shipped, and put the
expansion interface back into it whenever you need to store or transport it.
Installing
NOTE
• Before installing the expansion interface, you must rst always turn o the unit where
installing and unplug its power cord from the power outlet.
• When restarting the device with the expansion interface installed, wait several
seconds before turning on the power.

1. Loosen the EXPANSION SLOT mounting screws (2) on the device where you’re

installing, and detach the panel cover.

2. Insert the expansion interface into the EXPANSION SLOT.

* Do not touch any of the expansion interface pathways or connection terminals.
* Never use excessive force when installing a expansion interface. If it doesn’t t properly
on the rst attempt, remove the expansion interface
and try again.

3. Secure the expansion interface in place using the mounting screws (2).

Panel Descriptions

1
2
3
2
3
No. Name Explanation
1
VIDEO SYNC IN
connector
This is for input of a black-burst signal.
Here you connect a black-burst generator or other such external
source device when synchronizing the XI-MADI-compatible device
to video equipment.
2
MADI IN/OUT
connectors 1, 2
(optical)
These are optical-type connectors for MADI input and output.
* When no cable is used, attach the connector cap to prevent
entry by dust or other foreign matter. The unit is shipped from
the factory with the connector caps attached to the connectors.
About optical cables
• Use multi-mode ber-optic cable having a core diameter or
50/125 μm or 62.5/125 μm.
• Cable length can be up to 2,000 meters per cable.
• Use SC connectors compliant with ISO/IEC 9314-3.
3
MADI IN/OUT
connectors 1, 2
(coaxial)
These are BNC-type connectors for MADI input and output.
About coaxial cables
• Use cables whose impedance is 75 Ω.
• Cable length can be up to 100 meters per cable.
• Use BNC-type connectors compliant with IEC 60169-8.
• Canare L-5C2VS cable or equivalent is recommended.

Main Features

MADI (Multichannel Audio Digital Interface) is a transmission standard for digital audio
standardized by AES. An extension of the AES/EBU standard for stereo (two-channel)
transmission, it permits transmission of up to 64 channels over a single cable.
The main features of the XI-MADI are as follows.
• Equipped with two types of MADI connectors: optical and BNC
Optical and BNC (coaxial) MADI connectors are provided. You can select separate
connectors for both MADI 1 and MADI 2.
* When signals on the same channel are input via both the optical connector and the
BNC connector, the BNC input takes priority.
* Once optical input has been selected, the system does not switch to BNC as long as
an optical signal continues to be input.
* Depending on the equipment in which the XI-MADI is installed, locking input to
optical or BNC might be possible.
• Support for redundant main and backup transmission
Using a MADI 1 connector as main and a MADI 2 connector as backup is possible. In the
event of a problem with the main connection, the system automatically switches to the
backup connection.
* Redundant transmission uses either all-optical or all-BNC connections. Redundant
transmission combining optical with BNC is not supported.
• Equipped with a VIDEO SYNC IN connector
A VIDEO SYNC IN connector allowing black-burst signal input is provided. Selecting
the VIDEO SYNC IN connector as the clock source enables synchronization with video
equipment.
* For information on the equipment in which the XI-MADI can be installed, check the
following Roland website.
http://proav.roland.com
Thank you, and congratulations on your choice of the XI-MADI expansion
interface.
Installing this expansion interface card in professional audio equipment
from Roland makes it possible to expand audio input and output using
MADI (Multichannel Audio Digital Interface).
For information on devices on which the XI-MADI expansion interface
can be installed, check the Roland website.
http://proav.roland.com

Setup Guide

Copyright © 2015 ROLAND CORPORATION

Main Specications

Channels Up to 64 channels input/output x 2 (48 kHz, 44.1 kHz, 64 ch mode)
Up to 32 channels input/output x 2 (96 kHz, 64 ch mode)
* The number of available channels will be changed by the device that
attach the XI-MADI.
Signal
Processing
Sampling Frequency 96 kHz, 48 kHz, 44.1 kHz
MADI channel mode 64 ch, 56 ch
Data Length 24 bits
Connectors
Coaxial MADI IN (1, 2) connectors BNC type
Coaxial MADI OUT (1, 2) connectors BNC type
Optical MADI IN/OUT (1, 2)connectors SC duplex multi mode type (*1)
VIDEO SYNC IN connector BNC type
USB COMPUTER port
(Inside of the panel, updates only)
USB type B
Power
Consumption
7.0 W
Dimensions 120 (W) x 185 (D) x 40 (H) mm
4-3/4 (W) x 7-5/16 (D) x 1-5/8 (H) inches
* Protruding parts not included.
Weight 250 g
9 oz
Operation
Temperature
+5 to +40 degrees Celsius
+41 to +104 degrees Fahrenheit
Accessories
Setup Guide, Ferrite core x 5
(*1): For single mode type, consult your Roland vendor.
* In the interest of product improvement, the specications and/or appearance of this unit
are subject to change without prior notice.

Attaching Ferrite Cores

Attach ferrite cores to cables connected to the MADI IN/OUT connectors (coaxial) or VIDEO
SYNC IN connector.
* The ferrite cores are needed to prevent electromagnetic noise. Be sure to attach ferrite
cores to any cables connected to the MADI IN/OUT connectors (coaxial) or the VIDEO
SYNC IN connector.

1. Open an included ferrite core by spreading apart the tabs at two places.

2. Attach the ferrite core at a location near the plug base.

Close the ferrite core by pressing down on each tab until it clicks into place.
MEMO
Connect the plug at the end where the ferrite core is attached to the connector on the
other device.
s

Consultez gratuitement le manuel de la marque Roland XI-MADI ici. Ce manuel appartient à la catégorie Non catégorisé et a été évalué par 1 personnes avec une moyenne de 7.5. Ce manuel est disponible dans les langues suivantes: Anglais. Vous avez une question sur le XI-MADI de la marque Roland ou avez-vous besoin d’aide? Posez votre question ici

Besoin d’aide?

Vous avez une question sur le Roland et la réponse n'est pas dans le manuel? Posez votre question ici. Fournissez une description claire et complète du problème, et de votre question. Plus votre problème et votre question sont clairement énoncés, plus les autres propriétaires de Roland ont de chances de vous fournir une bonne réponse.

Nombre de questions : 0

Généralités
Roland
XI-MADI | XI-MADI
Non catégorisé
4957054506247
Anglais
Mode d’emploi (PDF)
Informations sur l'emballage
Quantité1
Guide d'installation rapideOui
Design
InterneOui
Couleur du produitNoir
Connectivité
Interface de l'hôte-
Interface de sortieBNC
Puissance
Consommation électrique typique7 W
Consommation électrique typique7 W
Poids et dimensions
Largeur120 mm
Profondeur185 mm
Hauteur40 mm
Poids250 g
Largeur120 mm
Profondeur185 mm
Hauteur40 mm
Poids250 g
Conditions environnementales
Température d'opération5 - 40 °C
Caractéristiques
InterneOui
Interface de l'hôte-
Couleur du produitNoir
CompatibilitéRoland M-5000
voir plus

Vous ne trouvez pas la réponse à votre question dans le manuel? Vous trouverez peut-être la réponse à votre question dans la FAQ sur le Roland XI-MADI au dessous de.

Votre question n'est pas dans la liste ? Posez votre question ici

Aucun résultat