Römer TRIFIX

Römer TRIFIX mode d'emploi

(1)
  • 03
    04
    05
    06
    07
    08
    12
    13
    14
    15
    17
    01
    02
    16
    09
    10
    11
    18
    TWO-YEAR WARRANTY
    CARE AND MAINTENANCE
    Seat shell
    ISOFIX locking arms
    Fabric loop
    User guide compartment
    Top Tether
    ISOFIX indicators
    ISOFIX unlocking buttons
    Recline handle
    Adjustment strap
    Adjusting button
    Shoulder straps
    Shoulder pads
    Harness buckle
    Harness retainer
    Headrest
    ISOFIX insert guides
    ISOFIX attachment points (car)
    10
    17
    12
    11
    09
    08
    07
    06
    05
    04
    03
    02
    01
    Please observe the instructions on the use of child restraint systems described in
    your vehicle owner’s manual.
    The seat may be used in all vehicles equipped with the ISOFIX and Top Tether
    anchoring systems. Please consult your vehicle owners manual for information
    about the Top Tether anchoring points and the seats which are approved for child
    safety seats in the weight class 9-18 kg.
    BRITAX RÖMER
    Child safety seats
    Testing and certi cation in accordance with ECE R 44/04
    Group Body weight
    KID 2 - 3 15 - 36 kg
    KID plus 2 - 3 15 - 36 kg
    KIDFIX 2 - 3 15 - 36 kg
    KIDFIX SICT 2 - 3 15 - 36 kg
    In the direction of travel Yes
    Against the direction of travel No
    1)
    On seats featuring:
    ISOFIX attachments (between
    seat surface and backrest) and
    Top Tether anchoring points (for
    example on the parcel shelf, on
    the  oor or behind the backrest)
    Yes
    2)
    NEXT CHILD SAFETY SEATS
    USE IN THE VEHICLE
    1) Use is permitted on a rearward-facing vehicle seat (e.g. in a van or minibus)
    only if the vehicle seat is also approved for use by adults. The seat must not be
    positioned anywhere where it is in range of an airbag which is being deployed.
    2) If there is a front airbag: Slide the passenger seat a long way back and refer to
    any instructions in vehicle owner’s manual.
    *ECE = European Standard for Child safety Equipment
    BRITAX RÖMER
    child safety seat
    Tested and certi ed according
    to ECE* R 44/04
    Group Body weight
    TRIFIX 1 9 bis 18 kg
    The child safety seat has been designed, tested and certi ed according to the requirements of the European
    Standard for Child Safety Equipment (ECE R 44/04). The test mark E (in a circle) and the certi cation number
    are located on the orange certi cation sticker (sticker on the child safety seat).
    This certi cation will be invalidated if you make any modi cations to the child safety seat.
    The TRIFIX child safety seat must only be used to secure your child in the vehicle. It must never be used as a
    seat or toy in the home.
    To ensure the full protective effect of the child safety seat:
    • In the event of an accident with an impact speed above 10
    km/h it is possible that the child safety seat may have been
    damaged, but that the damage may not be immediately
    obvious. In this case the child safety seat must be replaced.
    Please dispose of it properly.
    • Regularly check all important parts for damage. Make sure
    that the mechanical components in particular are all in per-
    fect working order.
    • To prevent damage, ensure that the child safety seat does
    not become jammed between hard objects (car door, seat
    runners etc.).
    Always have the child safety seat checked if it has been da-
    maged (e.g. if it is dropped).
    • Never lubricate or oil parts of the child seat.
    Please observe the waste disposal regulations in your country.
    For this child safety seat we offer a 2-year warranty against manufacturing or
    material defects. The warranty period is effective from the day of purchase.
    The warranty covers only child safety seats which have been handled properly
    and which have been sent to us in a clean and proper condition.
    The Warranty does not cover:
    • natural signs of wear and damage resulting from excessive stress
    • damage resulting from inappropriate or improper use
    What is covered by the warranty?
    Fabrics: All of our fabrics meet very high requirements with regard to colour
    fastness when exposed to UV radiation. Nevertheless, all fabrics fade when
    exposed to UV radiation. This is not a material defect, but rather a normal sign
    of wear which is not covered by the warranty.
    Buckle: Buckle malfunctions are often due to accumulations of dirt or foreign
    bodies which may stop the buckle from working properly. If this happens, the
    buckle can be cleaned, olease follow the procedure described in your user
    instructions.
    Please contact your retailer immediately in the event of a warranty claim. He or
    she will give you the advice and support you need. When processing claims,
    product-speci c depreciation rates will be applied. Please refer to our General
    Terms and Conditions which are available from your retailer.
    Use, care and maintenance
    The child safety seat must be used in accordance with the user instructions.
    We point out expressly that only genuine accessories and replacement parts
    must be used.
    (Please observe the applicable regulations in your country)
    Adjusting ring of the headrest
    13
    14
    15
    16
    18
    CARE INSTRUCTIONS
    Disposal of packaging Container for cardboard
    Cover Residual waste, thermal utilisation
    Plastic parts In accordance with the labelling in the
    designated container
    Metal parts Container for metals
    Harness straps Container for polyester
    Buckle &latch Residual waste
    PRODUCT OVERVIEW
    Care for the harness buckle
    It is vital for the safety of your child that the harness buckle works correctly.
    Malfunctions of the harness buckle are usually caused by accumulations of dirt
    or foreign bodies:
    • The buckle latches are ejected only slowly when the red release button is
    pressed.
    • The buckle latches will no longer lock home (i.e. they are ejected again if you
    try to push them in).
    • The buckle latches engage without an audible „click“.
    • The buckle latches are dif cult to insert (you feel resistance).
    • The buckle only opens if extreme force is applied.
    Remedy
    wash out the harness buckle so that it functions properly once again:
    Cleaning the harness buckle
    1. Open the harness buckle
    05
    (press the red button).
    2. Pull the elastic loop over the harness buckle
    05
    .
    2. Open the Velcro fastener on the crotch pad
    20
    and take off the crotch pad
    from the cover.
    3. Slide the metal plate
    22
    which is used to fasten the harness buckle
    05
    to
    the seat shell up on its edge through the strap slot
    31
    .
    4. Soak the harness buckle
    05
    in warm water with dishwashing liquid for at
    least an hour. Then rinse and dry it thoroughly.
    Cleaning
    Please be sure to use only genuine Britax/RÖMER replacement seat covers,
    as the seat cover is an integral part of the child safety seat which plays an
    important role in ensuring that the system works properly. Replacement
    seat covers are available from your retailer.
    • The child seat must not be used without its cover.
    • The cover can be removed and washed with a mild detergent using the
    washing machine‘s cycle for delicate items (30 °C). Please observe the
    instructions on the washing label of the cover.
    • The plastic parts can be cleaned using soapy water. Do not use harsh
    cleaning agents (such as solvents).
    • The harnesses can be washed in lukewarm soapy water.
    Caution: Never remove the buckle latches
    21
    from the straps.
    • The shoulder pads can be washed in lukewarm soapy water.
    Removing the cover
    1. Press the recline handle
    10
    upwards and slide the seat shell
    18
    to the rear
    into the upright position.
    2. Loosen the harness straps as far as possible.
    3. Open the harness buckle
    05
    (press the red button).
    4. Open the Velcro fastener on the crotch pad
    20
    .
    5. Slide the headrest
    03
    to its lowest position.
    6. Remove the cover of the headrest
    31
    .
    7. Open the poppers on the left and right of the rear part of the cover.
    8. Fold the rear part of the cover onto the seat surface.
    9. Thread the harness straps through the cutout in the cover.
    10. Unhook both of the elastic hoops at the rear, upper edge of the seat shell.
    11. Unhook the elastic seam of the cover under the edge of the seat shell.
    TIP: Start at the handles on the side and at the upper edge of the seat shell.
    12. Pull the cover up and over the bezel of the strap adjuster.
    13. Feed out the harness buckle
    05
    and the end of the strap from the cover.
    14. Pull the cover upwards a little and then put it with the cutout over the head-
    rest
    03
    .
    Re- tting the Cover:
    Simply follow the steps in the opposite order.
    Caution: Check that the harness straps are not twisted and that they have
    been correctly inserted in the belt slots on the cover.
    BRITAX RÖMER
    Kindersicherheit GmbH
    Blaubeurer Straße 71
    D-89077 Ulm
    Germany
    t: +49 (0) 731 9345 0
    f: +49 (0) 731 9345 210
    e: info@de.britaxeurope.com
    www.roemer.eu
    BRITAX EXCELSIOR LIMITED
    1 Churchill Way West
    Andover
    Hampshire SP10 3UW
    United Kingdom
    t: +44 (0) 1264 333343
    f: +44 (0) 1264 334146
    e: helpline@uk.britaxeurope.com
    www.britax.eu
    TRIFIX
    9 - 18kg
    User Instructions
    GB
    05
    20
    22
    31
    05
    20
    03
    31
    10
    User_guide_TRIFIX_GB.indd 1 17.01.2012 08:47:05
Römer TRIFIX

Besoin d’aide?

Nombre de questions : 0

Vous avez une question sur le TRIFIX de la marque Römer ou avez-vous besoin d’aide? Posez votre question ici. Fournissez une description claire et complète du problème et de votre question. Plus votre problème et votre question sont détaillés, plus il sera facile pour les autres propriétaires du TRIFIX de la marque Römer de répondre correctement à votre question.

Consultez gratuitement le manuel de la marque Römer TRIFIX ici. Ce manuel appartient à la catégorie Sièges de voiture et a été évalué par 1 personnes avec une moyenne de 5.7. Ce manuel est disponible dans les langues suivantes: Anglais. Vous avez une question sur le TRIFIX de la marque Römer ou avez-vous besoin d’aide? Posez votre question ici

Spécifications du TRIFIX de la marque Römer

Généralités
Marque Römer
Modèle TRIFIX
Produit Siège de voiture
EAN 4000984096972, 4000984096989
Langue Anglais
Type de fichier PDF
Poids et dimensions
Largeur 450
Profondeur 540
Hauteur 650
Poids 10800
Caractéristiques
Groupe siège auto 1 (9 - 18 kg; 9 mois - 4 ans)
Type de montage ISOFIX
Type de courroie de fixation 5 points
Appuie-tête réglable
Protection latérale
Couleur du produit Black, White

Foire aux questions

Ci-dessous, vous trouverez les questions les plus fréquemment posées à propos de Römer TRIFIX.

Votre question n'est pas dans la liste ? Posez votre question ici

ModesdEmploi.fr

Vous cherchez un manuel ? ModesdEmploi.fr vous permet de trouver le manuel que vous recherchez en un rien de temps. Notre base de données contient plus d'un million de manuels en PDF pour plus de 10 000 marques. Chaque jour, nous ajoutons les derniers manuels afin que vous trouviez toujours le produit que vous recherchez. C'est très simple : entrez le nom de la marque et le type de produit dans la barre de recherche pour consulter gratuitement et immédiatement le manuel de votre choix en ligne.

ModesdEmploi.fr

© Copyright 2020 ModesdEmploi.fr. Tous droits réservés.

Nous utilisons des cookies pour vous garantir la meilleure expérience sur notre site. Si vous continuez à utiliser ce dernier, nous considérerons que vous acceptez l'utilisation des cookies.

En savoir plus