Shark Professional Steam Power Iron mode d'emploi

Shark Professional Steam Power Iron
7 · 2
PDF mode d'emploi
 · 2 pages
Français
mode d'emploiShark Professional Steam Power Iron
This manual covers model numbers: GI405 55, GI405C 55Euro-Pro Operating LLC Newton, MA 02459 1-800-798-7398COPYRIGHT© EURO-PRO OPERATING LLC 2013PRINTED IN CHINA Illustrations may differ from actual product.Euro-Pro and Shark are trademarks of Euro-Pro Operating LLC.

BEFORE FIRST TIME USE

1 Before using your iron for the first time, please remove all the packaging material.2 When you turn on the iron for the first time it might emit an odor for the first ten minutes. This is because the materials used in making the iron are heating up. The odor is safe and should not re-occur after the initial heating.

USING YOUR IRON

3 Pour water carefully into the water tank without going over “MAX” line. Make sure the water inlet cover is closed to avoid spilling while in use.4 Plug in the iron into any 120V AC polarized electrical outlet. The LED Indicator Light below the Power on the Fabric Selector Dial will light up.5 Set the desired ironing temperature by turning the Fabric Selector Dial. 6 The LED Indicator Light above the selected temperature will flash and then will become green once the selected temperature is reached. If you wish to change the temperature, the LED Indicator Light will start to flash to show that the iron is either heating up or cooling down. The LED Indicator Light will turn green again when the iron reaches the selected temperature.
7 Press the Variable Steam Control Lever to select high or low steam setting. Select
“ ” on the steam lever for dry ironing. You can now start ironing.8 Use the Steam Burst Button to remove stubborn wrinkles. Allow an interval of 3 seconds between each burst. Overuse of the steam burst may cause water spitting or weak steam performance.
9 The Steam Burst feature also works in the vertical position. This is especially useful to
remove wrinkles from hanging clothes, delicate garments and other fabrics. Hold the iron in the upright position several inches away from the article. 10 Use the Spray Button to dampen the fabric to tackle tough wrinkles, if necessary.

ANTI-DRIP FUNCTION

11 The Anti-Drip Function is built in to this iron. It prevents water spitting when the temperature is too low.12 Steam cannot be produced if the soleplate is not hot enough. It may result in water spitting or leaking from the soleplate. The Anti-Drip Function reduces water dripping and leaking when ironing at low temperatures.

ELECTRONIC MULTI POSITION AUTO-OFF

13 This iron is equipped with an electronic auto-off feature that switches the iron off if
it has been idle for 15 minutes in the upright position and after 30 seconds in the sideways or flat positions.
14 The LED Indicator Light above the Auto-Off on the Fabric Selector Dial will flash in red
when the iron is in auto-off mode. To turn the iron back on, gently rock the iron back and forth several times until the LED Indicator Light is re-illuminated. The iron might have to warm up for a minute if the auto-off feature was activated for an extended time.

SELF-CLEANING

15 Fill the water tank to the “MAX” level. Do not overfill.16 Stand the iron on its heel, standing up on a protected surface and plug into the electrical outlet.
17 Set the Fabric Selector Dial to “Linen/Cotton” setting. Wait until the light stops flashing.
The iron is now on the preset temperature.
18 Hold the iron horizontally over the sink. Press and hold the Variable Steam/Self Clean
Lever all the way down to the SELF CLEAN position.19 Move the iron back and forth. Boiling water and steam will now be ejected from the holes in the soleplate. Use caution when doing this as the water and the steam are hot enough to cause burns.20 Repeat step 19 until the impurities and scale are washed away.21 Empty any excess water from the tank. Don’t touch the hot surfaces, water or steam because injury may occur.22 Release the steam lever and it will automatically go to “ ”.23 Place the iron in upright position and let it cool down.

USEFUL TIPS

24 Read all garment care labels before you start ironing. You can also test the temperature of the iron on a hem or an inside seam. 25 Iron similar fabrics together and in sequence of synthetic fibers nylon, silk/wool, polyester, and cotton/linen. This will reduce the need to adjust the temperature frequently.TECHNICAL SPECIFICATIONS: 120 Volts, 60 Hz., 1600 Watts

IRONING GUIDE

FEATURES

STORAGE AND CARE

26 Always set the Variable Steam Control Lever to “ ” after you have emptied the water
tank.27 Allow the iron to cool down before putting it away.28 Place the iron in the upright position during heating up, cooling down and storage.29 Avoid any sharp material contacting the soleplate.30 Every two weeks, clean the exterior of the iron with a damp cloth and wipe dry.31 If you use spray starch, wipe the soleplate occasionally with a soft, damp cloth to prevent deposit build-up.32 If the iron hasn’t been used in a few weeks, hold the iron horizontally and allow steaming for 2 minutes before ironing.

ALWAYS REMEMBER

33 Turn the Fabric/Selector Dial to “Nylon” and then unplug the iron from the electrical outlet before pouring water into the iron.34 Always empty the water in the iron after each use.35 Never iron or steam clothes while they are being worn.36 Be very careful when filling the iron with water. Injuries may occur if the hot metal parts, hot water or steam are contacted.

TROUBLE SHOOTING

This appliance has a polarized plug (one blade is wider than the other). As a safety feature, this plug will fit into a polarized outlet only one way. If the plug does not fit fully into the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not attempt to defeat this safety feature.The iron doesn’t heat up.An odor is being emitted from the new iron or small particles are coming out.Iron doesn’t steam.Water droplets coming from steam vents.Iron should be plugged into a 120V AC electric outlet only.Make sure the plug is securely in the socket.Temperature setting might be too low.Try turning to a higher setting.Auto-off feature is activated.This is normal. Follow the instructions for first-time use and allow iron to steam through 2-3 fillings and press the steam burst button occasionally to eliminate small white particles.Water tank may be empty or water level is very low. Add water.Make sure the fabric setting and the Variable Steam Control Lever are correctly set. For maximum steam, set the Variable Steam Control Lever to “ ” and the temperature setting should be set on “Linen/Cotton.”Steam control is set on “ ”.The soleplate is not hot enough and the anti-drip feature switches off the steam. Always allow the iron to reach the selected temperature with the Variable Steam Control Lever setting at “ ”. For more steam, turn Fabric Selector Dial to a higher setting and the steam control to “ ” If the temperature setting and steam control settings are correct and there is no steam, gently move the iron left or right a couple of times. Move the Variable Steam Control Lever from “ ” to “ ” a few times. Variable Steam Control Lever may be set in “Self Clean” position. Align the lever to the “ ” to “ ” steam setting. Iron may not be hot enough. Set temperature to “Linen/Cotton” position. Always allow iron sufficient time to heat up before activating the variable steam control.The Steam Burst may have been overused. Allow more time between each burst.

SAVE THESE INSTRUCTIONS

ONE YEAR LIMITED WARRANTY

EURO-PRO Operating LLC warrants this product to be free from material defects and workmanship for a period of one (1) year from the date of purchase when utilized for normal household use, subject to the following conditions, exclusions and exceptions.The liability of EURO-PRO Operating LLC is limited solely to the cost of the repair or replacement of the unit at our option. This warranty does not cover normal wear of parts and does not apply to any unit that has been tampered with or used for commercial purposes. This limited warranty does not cover damage caused by misuse, abuse, negligent handling or damage due to faulty packaging or mishandling in transit. This warranty does not cover damage or defects caused by or resulting from damages from shipping or repairs, service or alteration to the product or any of its parts, which have been performed by a repair person not authorized by EURO-PRO Operating LLC.If your appliance fails to operate properly while in use under normal household conditions within the warranty period, you may return the complete appliance and accessories with proof of purchase and date, freight prepaid. For customer service
support, call 1-800-798-7398 or visit our website at www.sharkclean.com.
If the appliance is found by EURO-PRO Operating LLC to be defective, in EURO-PRO Operating LLC’s sole discretion, we will repair or replace it free of charge. Proof of purchase date and check made payable to EURO-PRO Operating LLC in the amount of $12.95 to cover the cost of return shipping and handling must be included.This warranty is extended to the original purchaser of the unit and excludes all other legal, implied and/or conventional warranties. The responsibility of EURO-PRO Operating LLC if any, is limited to the specific obligations expressly assumed by it under the terms of this Limited Warranty. In no event is EURO-PRO Operating LLC liable for incidental or consequential damages to anyone of any nature whatsoever. Some states do not permit the exclusion or limitation of incidental or consequential damages, so the above may not apply to you.This Limited Warranty gives you specific legal rights, and you may also have other rights which vary from state to state or province to province. *IMPORTANT: Carefully pack item to avoid damage in shipping. Be sure to include proof of purchase date and to attach a tag to item before packing including your name, complete address and phone number with a note giving purchase information, model number and what you believe is the problem with the item. We recommend you insure the package (as damage in shipping is not covered by your warranty). Mark the outside of your package “ATTENTION CUSTOMER SERVICE”. We are constantly striving to improve our products, therefore the specifications contained herein are subject to change without notice.
CAUTION! TO PREVENT ELECTRIC SHOCK OR OTHER INJURY, before filling the iron with
water, make sure that the plug is removed from the outlet.
WARNING: Never fill the iron with fabric conditioner, starches or any other solution, as
these will damage the steam mechanism. Do not use contaminated water.
CAUTION! TO AVOID FIRE, never leave iron unattended while it is plugged in.
CAUTION! TO PREVENT ELECTRIC SHOCK, never use the iron in a location where it can
fall or be pulled into water or another liquid. If the iron falls into water or other liquid, unplug it immediately. DO NOT reach into the water or liquid.
WARNING: Never use scouring pads, abrasive or chemical cleaners, or solvents to clean
the exterior or soleplate of your iron. Doing so will scratch and/or damage the surface.
CAUTION! DO NOT aim iron at face, towards yourself, or anyone else while using or
adjusting steam. Burns or serious injury may occur.

SPECIAL INSTRUCTIONS

1. To avoid a circuit overload, do not operate another high-wattage appliance on the same
circuit.
2. If an extension cord is absolutely necessary, use a 15-ampere cord. Cords rated for less
amperage can result in a risk of fire or electric shock due to overheating. Use care to arrange the extension cord so it cannot be pulled or be tripped over.

IMPORTANT SAFETY INSTRUCTIONS

READ ALL INSTRUCTIONS BEFORE USING YOUR IRONWhen using your iron, basic safety precautions should always be followed, including the following:1. Use iron only for its intended use.
2. To protect against risk of electrical shock, do not immerse the iron in water or other
liquids.3. DO NOT yank cord to disconnect from outlet. Grasp plug and pull to disconnect.4. DO NOT allow cord to touch hot surfaces. Turn the Fabric Selector Dial to “Nylon” before unplugging the iron. Let iron cool completely before putting away. Loop cord loosely around iron when storing.
5. Always disconnect iron from electrical outlet when filling with water, emptying, or when
not in use.
6.
DO NOT operate iron with a damaged cord, or after the iron has been dropped or damaged in any manner, or if it is leaking. To avoid the risk of electric shock, do not disassemble the iron. Return to EURO-PRO Operating LLC for examination, repair, or adjustment. Incorrect reassembly can cause the risk of electric shock when the iron is used.
7. IMPORTANT: This appliance is not intended for use by persons (including children)
with reduced physical, sensory or mental capabilities, or lack of experience and knowledge.
Close Supervision is necessary for any appliance being used near children. DO
NOT leave iron unattended while connected or on an ironing board.8. Burns can occur from touching hot metal parts, hot water, or steam. Use caution when you turn a steam iron upside down; there may be hot water in the reservoir.
9. DO NOT use or stand the iron on an unstable surface.
10. While the iron is hot, never set iron on an unprotected surface - even if it is on its heel
rest.
11. Always store your iron standing upright, not on the soleplate. If stored face down, even
the smallest amount of moisture will cause the soleplate to corrode and stain.12. This appliance is for household use only.GI405series_55.E.F.130822.3
8
FABRIC TYPELABELINDICATIONTEMPERATURESELECTORSTEAMCONTROLBURST OFSTEAMSPRAYPlease note that the symbol above on the label of your garment means that THE ARTICLE CANNOT BE IRONEDNONO NO YESYESYES YES YESNylon
Wool/SilkPolyester
Linen/Cotton
LOW LOW - MED. MED. HIGH
1 Stainless Steel Soleplate2 Water Inlet Door3 Spray Button 4 Water Level Window5 Spray Nozzle6 Variable Steam/Self-Clean Control Lever7 Steam Burst Button8 Fabric Selector Dial9 Pivot Cord10 LED Indicator Light11 Anti-Drip Function (not shown)
3
5
6
1
10
2
7
4
9
8
10

OWNER’S GUIDE

GI405 series

Mode d'emploi

Consultez gratuitement le manuel de la marque Shark Professional Steam Power Iron ici. Ce manuel appartient à la catégorie Fers à repasser et a été évalué par 2 personnes avec une moyenne de 7. Ce manuel est disponible dans les langues suivantes: Français, Anglais. Vous avez une question sur le Professional Steam Power Iron de la marque Shark ou avez-vous besoin d’aide? Posez votre question ici

Besoin d’aide?

Vous avez une question sur le Shark Professional Steam Power Iron et la réponse n'est pas dans le manuel? Posez votre question ici. Fournissez une description claire et complète du problème, et de votre question. Plus votre problème et votre question sont clairement énoncés, plus les autres propriétaires de Shark Professional Steam Power Iron ont de chances de vous fournir une bonne réponse.

Nombre de questions : 0

Spécifications du Professional Steam Power Iron de la marque Shark

Vous trouverez ci-dessous les spécifications du produit et les spécifications du manuel du Shark Professional Steam Power Iron.

Généralités
Marque Shark
Modèle Professional Steam Power Iron
Produit Fer à repasser
EAN 622356532259, 0622356532259
Langue Français, Anglais
Type de fichier Mode d’emploi (PDF)
Caractéristiques
Type Fer à repasser à sec ou à vapeur
Vapeur variable Oui
Longueur du câble - m
Performances de jet de vapeur - g/min
Matériau/revêtement de la semelle Semelle en acier inoxydable
Couleur du produit Blue,Grey
Capacité du réservoir d'eau 0.3 L
Système anti-goutte Oui
Fonction Spray Oui
Coupure automatique de l'alimentation Oui
Anti calc automatique -
Vapeur continue - g/min
Températures préprogrammées Oui
Fonction augmenter la vapeur -
Autonettoyant Oui
Poignée douce au toucher Oui
Voyants Oui
Mise hors tension automatique après 15 min
Sans fil Non
Puissance
Puissance 1600 W
Tension d'entrée AC 120 V
Fréquence d'entrée AC 60 Hz
Indication
Indicateur de niveau d'eau Oui
Lumière d'indication Oui
Ergonomie
Corde de non-torsion Oui
Contenu de l'emballage
Verre mesureur Oui
voir plus

Foire aux questions

Vous ne trouvez pas la réponse à votre question dans le manuel? Vous trouverez peut-être la réponse à votre question dans la FAQ sur le Shark Professional Steam Power Iron au dessous de.

Votre question n'est pas dans la liste ? Posez votre question ici

Aucun résultat