Sony ICD-B16

Sony ICD-B16 mode d'emploi

(1)
  • 3-264-832-11 (1)
    IC Recorder
    Operating Instructions
    2004 Sony Corporation Printed in China
    ICD-B16/B26
    Owner’s Record
    The model number is located at the rear and the serial number is located inside the battery
    compartment. Record the serial number in the space provided below. Refer to these numbers
    whenever you call upon your Sony dealer regarding this product.
    Model No. ICD-B16/B26 Serial No.
    Step 1: Installing the Batteries
    Slide and lift the battery
    compartment lid.
    Insert two LR03 (size AAA)
    alkaline batteries with
    correct polarity, and close the
    lid.
    If the battery compartment lid
    is accidentally detached,
    attach it as illustrated.
    1
    2
    Clock setting display appears when you insert batteries for the first time, or
    when you insert batteries after the unit has been without batteries for a certain
    period of time. Please refer to Steps 2 to 3 in “Step 2: Setting the Clock” to set the
    date and time.
    Replacing the batteries
    The battery indicator on the display
    window shows the battery
    condition.
    When
    flashes, replace the
    batteries with new ones.
    When
    flashes, the batteries are
    exhausted and the unit will stop
    operation.
    Battery life*
    With continuous use, approx. 18.5
    hours recording/9.5 hours playback in
    the SP mode and 19.5 hours
    recording/10 hours playback in the
    LP mode is possible.
    * Using Sony alkaline batteries LR03
    (size AAA)
    * When playing back through the
    internal speaker with VOL control at
    around 4
    The battery life may shorten
    depending on the operation of the
    unit.
    Notes
    Do not use manganese batteries for
    this unit.
    When you replace the batteries,
    insert the new ones within 3
    minutes after you removed the
    exhausted ones. Otherwise, the
    display may show the clock setting
    display or incorrect date and time
    when you reinsert the batteries. In
    this case, set the date and time
    again.
    The recorded messages and alarm
    setting, however, will remain.
    When replacing the batteries, be
    sure to replace both batteries with
    new ones.
    • Do not charge dry batteries.
    When you are not going to use the
    unit for a long time, remove the
    batteries to prevent damage from
    battery leakage and corrosion.
    Clock setting display appears when you insert batteries for the first time, or when you insert battery after the unit has been
    without battery for a certain period of time. In this case, proceed from step 2.
    Display the clock setting display.
    Set the date.
    2 Press NxPLAY/STOP.
    The month digits will flash.
    3 Set the month and day in sequence,
    then press NxPLAY/STOP.
    The hour digits will flash.
    1
    2 Press – . once to display “SET
    DATE”.
    3 Press NxPLAY/STOP.
    The year digits will flash.
    1 Tip
    To set the date to Year 2004, display
    “04Y”.
    2
    Step 2: Setting the Clock
    Set the time.
    3
    3 Set the minute.
    4 Press NxPLAY/STOP at the time
    signal.
    The display will return to “SET
    DATE”.
    5 Press MENU to exit from the menu
    mode.
    Recording Messages
    You can record up to 99 messages in each of the two folders (A and B).
    Since a newly recorded message is automatically added behind the last recorded
    message, you can start recording quickly without searching for the end of the
    last recording.
    Note
    Before making a long recording, be sure to insert new batteries and check the battery
    indicator.
    Select the folder.
    Start recording.
    You do not need to keep pressing zREC/STOP while recording.
    1 Press zREC/STOP.
    Stop recording.
    If you do not change the folder after you stop recording, the next time you
    record you will record in the same folder.
    To Do this
    pause recording* Press XPAUSE.
    During recording pause, the
    OPR indicator flashes in red and
    “PAUSE” flashes in the display
    window.
    release pause and Press XPAUSE or zREC/STOP.
    resume recording Recording resumes from that point.
    (To stop recording after pausing recording, press
    STOP.)
    listen to the current Press zREC/STOP or STOP to stop recording,
    recording then press NxPLAY/STOP.
    review the current Press NxPLAY/STOP during recording.
    recording instantly
    select the microphone You can select the microphone sensitivity to display
    sensitivity the following by pressing MIC SENS.
    HIGH: To record at meeting or in a quiet and/or
    spacious place.
    LOW: To record for dictation or in a noisy place.
    * About one hour after you pause recording, recording pause is automatically released
    and the unit goes into the stop mode.
    3
    2
    e.g.
    XPAUSE
    Press zREC/STOP again.
    The unit stops at the
    beginning of the current
    recording.
    BBasic Operations
    Remaining memory
    indicator
    * The display selected
    with the DISPLAY
    button appears.
    Information
    IN NO EVENT SHALL SELLER BE LIABLE FOR ANY DIRECT,
    INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY
    NATURE, OR LOSSES OR EXPENSES RESULTING FROM ANY
    DEFECTIVE PRODUCT OR THE USE OF ANY PRODUCT.
    For the customers in the U.S.A.
    INFORMATION
    This equipment has been tested and found to comply with the
    limits for a Class B digital device, pursuant to Part 15 of the
    FCC Rules. These limits are designed to provide reasonable
    protection against harmful interference in a residential
    installation. This equipment generates, uses, and can radiate
    radio frequency energy and, if not installed and used in
    accordance with the instructions, may cause harmful
    interference to radio communications.
    However, there is no guarantee that interference will not occur
    in a particular installation. If this equipment does cause
    harmful interference to radio or television reception, which can
    be determined by turning the equipment off and on, the user is
    encouraged to try to correct the interference by one or more of
    the following measures:
    Reorient or relocate the receiving antenna.
    Increase the separation between the equipment and
    receiver.
    Connect the equipment into an outlet on a circuit different
    from that to which the receiver is connected.
    Consult the dealer or an experienced radio/TV technician
    for help.
    This device complies with Part 15 of the FCC Rules. Operation
    is subject to the following two conditions: (1) This device may
    not cause harmful interference, and (2) this device must accept
    any interference received, including interference that may
    cause undesired operation.
    You are cautioned that any changes or modifications not
    expressly approved in this manual could void your authority
    to operate this equipment.
    Precautions
    On power
    Operate the unit only on 3 V DC. Use two LR03 (size AAA)
    alkaline batteries.
    On safety
    Do not operate the unit while driving, cycling or operating
    any motorized vehicle.
    On handling
    Do not leave the unit in a location near heat sources, or in a
    place subject to direct sunlight, excessive dust or mechanical
    shock.
    Should any solid object or liquid fall into the unit, remove
    the batteries and have the unit checked by qualified
    personnel before operating it any further.
    On noise
    Noise may be heard when the unit is placed near an AC
    power source, a fluorescent lamp or a mobile phone during
    recording or playback.
    Noise may be recorded when an object, such as your finger,
    etc., rubs or scratches the unit during recording.
    On maintenance
    To clean the exterior, use a soft cloth slightly moistened in
    water. Do not use alcohol, benzine or thinner.
    Keep personal credit cards using magnetic coding or spring-
    wound watches, etc., away from the unit to prevent possible
    damage from the magnet used in the speaker.
    If you have any questions or problems concerning your unit,
    please consult your nearest Sony dealer.
    Backup recommendations
    To avoid potential risk of data loss caused by accidental
    operation or malfunction of the IC recorder, we recommend
    that you save a backup copy of your recorded messages on
    a tape recorder, etc.
    Current folder
    Press FOLDER to
    display the folder in
    which you wish to
    record messages.
    Note on recording
    Noise may be recorded if an object,
    such as your finger, etc., accidentally
    rubs or scratches the unit during
    recording.
    Maximum recording time
    The maximum recording time of all
    the folders is as follows. You can
    record messages for the maximum
    recording time in a single folder.
    Mode: SP* LP**
    ICD-B16 5 h. 8h. 15 min.
    ICD-B26 10 h. 16 h. 25 min.
    (h.: hours/min.: minutes)
    * SP: Standard play recording mode
    (monaural sound)
    ** LP: Long play recording mode
    (monaural sound)
    Notes
    To record in better sound quality,
    select the SP mode. For switching
    the recording mode, see “Changing
    the Recording Mode” on the reverse
    side.
    Before making a long recording, be
    sure to check the battery indicator.
    The maximum recording time and
    the number of messages you can
    make varies depending on the
    conditions of use.
    When you record messages in the
    mixture of SP and LP mode, the
    maximum recording time will be
    between those for the SP and LP
    modes.
    Due to the limitation of the IC
    recording system, this unit records
    in the minimum recording unit of
    approx. 9 seconds, therefore the
    following symptoms may occur:
    – When a message is shorter than
    the minimum recording unit, it is
    still counted as approx. 9 seconds
    so the remaining recording time
    will decrease by more than the
    actual length of the message.
    – When the message is longer than
    the minimum recording unit, the
    remaining recording time will
    decrease by more than the actual
    length of the message if it cannot
    be divided by the minimum
    recording unit without a
    remainder.
    –The sum of the number on the
    counter (elapsed recording time)
    and the remaining recording time
    may be less than the unit’s
    maximum recording time.
    Remaining memory
    indication
    During recording, the remaining
    memory indicator decreases one by
    one.
    When the remaining time of
    recording reaches 5 minutes, the
    last one of the indication flashes.
    When the remaining time of
    recording reaches 1 minute, the
    selected display mode and
    “REMAIN” will flash one after the
    other in the display window. When
    the memory is full, recording
    automatically stops and “FULL”
    will flash in the display window
    with an alarm sound. To continue
    recording, first erase some of the
    messages.
    Notes
    If you press zREC/STOP when the
    memory is full, “FULL” will flash
    with an alarm sound. Erase some of
    the messages before you start
    recording again.
    If you press zREC/STOP after you
    have recorded 99 messages, “FULL”
    will flash with an alarm sound.
    Select another folder or erase some of
    the messages.
    Starting recording
    automatically in response
    to the sound — Advanced
    VOR function (ICD-B26
    only)
    When VOR (voice operated
    recording) is set to ON in the menu,
    recording starts when the recorder
    detects sound. (“VOR” is displayed
    in the display window.)
    Recording stops when no sound is
    heard. (“VOR PAUSE” flashes in
    the display window.)
    Note
    VOR function is affected by the sound
    around you. Set the MIC SENS to
    HIGH or LOW. If recording is not
    satisfactory after you have changed
    the microphone sensitivity, or for
    important recording, set VOR to OFF.
    Flashing
    * The display selected with the DISPLAY button appears (see the reverse side).
    When playing back a previously recorded message, start from Step 1.
    When playing back a message you have just finished recording, start from Step 3.
    Select the folder.
    Select the message number.
    1
    Press FOLDER to display
    the folder you wish to
    play back.
    Press – . or >+ to
    display the desired
    message number.
    >+: for larger
    message number
    .: for smaller
    message number
    Selected message number
    Current folder
    Counter
    display*
    Playing Back Messages
    Start playback.
    After playing back one message, the unit stops at the beginning of the next
    message. When the continuous play function is set to “ON” (see the reverse
    side), the unit stops after playing all messages in a folder.
    When the last message on a folder has been played back, the unit stops at the
    beginning of the last message.
    For private listening
    Connect an ear receiver or headphones (not supplied) to the EAR jack. The built-
    in speaker will be automatically disconnected. If you plug in headphones, you
    will get output from the left channel only. If noise is heard, wipe the
    headphones plug.
    Other operations
    To Do this
    stop at the beginning of Press STOP.
    the current message
    stop at the current position Press NxPLAY/STOP.
    (Playback Pause function)* To resume playback from that point,
    press NxPLAY/STOP again.
    go back to the beginning Press – . once.
    of the current message
    skip to the next message Press >+ once.
    go back to previous Press – . or >+ repeatedly.
    messages/skip to succeeding (During stop mode, keep the button
    messages pressed to skip the messages
    continuously.)
    * You can also pause playback by pressing XPAUSE instead of NxPLAY/STOP.
    The OPR indicator will flash in green. After about one hour, the unit goes into the
    stop mode at the current position.
    2 Turn VOL to adjust the
    volume.
    EAR jack
    1 Press NxPLAY/STOP.
    BGetting started
    Troubleshooting
    Before taking the unit for repair, check the following
    sections. Should any problem persist after you have
    made these checks, consult your nearest Sony dealer.
    The unit does not operate.
    The batteries have been inserted with incorrect
    polarity.
    The batteries are weak.
    The buttons are locked with the HOLD switch. (If
    you press any button, “HOLD” will flash three
    times.)
    No sound comes from the speaker.
    Ear receiver or headphones are plugged in.
    The volume is turned down completely.
    “FULL” is displayed and you cannot start
    recording.
    The memory is full. Erase some of the messages.
    99 messages has been recorded in the selected
    folder. Select another folder or erase some of the
    messages.
    Noise is heard.
    An object, such as your finger, etc., accidentally
    rubbed or scratched the unit during recording so
    that noise was recorded.
    The unit was placed near an AC power source, a
    fluorescent lamp or a mobile phone during
    recording or playback.
    Plug of the connected microphone was dirty when
    recording. Clean the plug.
    Ear receiver/headphones plug is dirty. Clean the
    plug.
    Recording level is low.
    Press MIC SENS to display “HIGH”.
    Recording level is unstable (when recording
    music, etc.).
    This unit is designed to automatically adjust the
    recording level when recording meetings, etc., and
    is not suitable for music recording.
    “--Y--M--D” or “--:--” is displayed.
    You have not set the clock.
    “--Y--M--D” or “--:--” is displayed on the
    recorded date or recorded time display.
    The date and time of recording will not be
    displayed if you recorded the message when the
    clock was not set.
    You cannot divide a message.
    You cannot divide a message in a folder which has
    99 messages.
    If you divide messages frequently, the unit may
    become unable to divide a message.
    You cannot divide a message in the first or the last
    1 second of a message.
    You cannot combine a message.
    If you combine messages frequently, the unit may
    become unable to combine messages.
    You cannot record messages up to the
    maximum recording time.
    If you record messages in a mixture of SP and LP
    modes, the recordable time varies from the
    maximum SP mode recording time to the
    maximum LP mode recording time.
    No more recording can be made when 99 messages
    each have been recorded in both A and B folders.
    Due to the limitation of the IC recording system,
    this unit records in the minimum recording unit of
    approx. 9 seconds. If the length of each message
    cannot be divided by the minimum recording unit,
    the remaining recording time may decrease by
    more than the total length of the messages.
    The unit does not operate correctly.
    Take out the battery and insert it again.
    Please note that recorded messages may be erased
    during service or repair work.
    2
    Counter display (or the
    selected display mode)
    STOP
    NxPLAY/STOP
    MIC SENS
    * The “ALARM” display
    may appear instead of
    the “MODE” display.
    Current
    message
    number
    Counter display*
    1 Tip
    This unit does not have a power on/off
    switch. The display is shown at all
    times.
    Playing back a message
    repeatedly
    — Repeat Play
    During playback, press
    NxPLAY/STOP for more than
    one second.
    “ will be displayed and the
    selected message will be played
    back repeatedly.
    To resume normal playback, press
    NxPLAY/STOP again. To stop
    playback, press STOP.
    Playing the beginning of
    each message
    — Scanning Play
    During stop mode, press
    NxPLAY/STOP for more than
    one second.
    “SCAN” will be displayed in the
    display window and the first 5
    seconds of each message in the
    selected folder will be played back.
    When you find the desired
    message, press NxPLAY/STOP.
    The message will be played back
    until the end.
    Playing back all messages
    in a folder continuously
    — Continuous Play
    You can select the continuous play
    mode with the CONT in the menu.
    When you set CONT to ON, you
    can play back all messages in a
    folder continuously.
    Searching forward/
    backward during playback
    (Cue/Review)
    To search forward, keep >+
    pressed during playback and
    release the button at the point you
    wish to resume playback.
    To search backward, keep – .
    pressed during playback and
    release the button at the point you
    wish to resume playback.
    If you keep >+ or – .pressed
    for more than 10 seconds, the unit
    starts to search at higher speed.
    For the first 10 seconds of cue/
    review, fast playback sound can be
    heard. When searching at a higher
    speed, playback sound will not be
    heard.
    During cue/review, the counter
    will be displayed, regardless of the
    display mode setting.
    1
    Tip
    When fast playback is done to the end
    of the last message, “END” flashes 3
    times. (You cannot hear the playback
    sound.) If you keep – . pressed
    while “END” is flashing, the messages
    are played back rapidly, and normal
    playback will start at the point you
    release the button.
    When “END” stops flashing and the
    OPR indicator goes off, the unit will
    stop at the beginning of the last
    message.
    If the last message is long and you
    wish to start playback at a later part of
    the message, keep >+ pressed to
    play back the message to the end and
    then press – . while “END” is
    flashing to go back to the desired
    point .
    (For messages other than the last one,
    go to the beginning of the next
    message and play backward to the
    desired point.)
    1 Press MENU to enter the menu
    mode.
    1 Press – . or >+ to select
    the digits of the year.
    1 Press – . or >+ to select
    the digits of the hour.
    2 Press NxPLAY/STOP.
    The minute digits will flash.
    2 Speak to the
    built-in
    microphone.
    OPR indicator
    (lights in red during
    recording.)
    Message 1 Message 2 Blank spaceNewly recorded message
    OPR indicator
    (lights in green during
    playback.)
    The memory is
    nearly full.
    1
    Microphone
    sensitivity
    Recording mode
    Number of
    messages in a folder
    Number of
    messages
    in a folder
    STOP
    You can stop recording by
    pressing STOP instead of
    zREC/STOP.
    3
Sony ICD-B16

Besoin d’aide?

Nombre de questions : 0

Vous avez une question sur le ICD-B16 de la marque Sony ou avez-vous besoin d’aide? Posez votre question ici. Fournissez une description claire et complète du problème et de votre question. Plus votre problème et votre question sont détaillés, plus il sera facile pour les autres propriétaires du ICD-B16 de la marque Sony de répondre correctement à votre question.

Consultez gratuitement le manuel de la marque Sony ICD-B16 ici. Ce manuel appartient à la catégorie Enregistreurs audio et a été évalué par 1 personnes avec une moyenne de 6.5. Ce manuel est disponible dans les langues suivantes: Anglais. Vous avez une question sur le ICD-B16 de la marque Sony ou avez-vous besoin d’aide? Posez votre question ici

Spécifications du ICD-B16 de la marque Sony

Généralités
Marque Sony
Modèle ICD-B16
Produit Enregistreur audio
Langue Anglais
Type de fichier PDF
Autres caractéristiques
Dimensions (LxPxH) 105.3 x 44.5 x 14 mm
Type de batterie AAA
Poids et dimensions
Poids 68 g
Audio
Temps d'enregistrement maximal 8.15 h
Gamme de fréquence 160 - 3300 Hz
Microphone intégré Oui
Mode d'enregistrement Long Play (LP),Standard Play (SP)
Mémoire
Mémoire interne 16 Mo
Écran
Type d'écran LCD
Rétroéclairage Oui
Détails techniques
Fonction "Hold" Oui
Raccordement au PC Non
Connectivité
Entrée jack microphone Oui
Sortie casque audio Oui
Batterie
Autonomie maximum de la batterie 19.5 h
Enregistrement de la durée de vie de la batterie 10 h
Nombre de batteries prises en charge 2
Indicateur de capacité de la batterie Oui
Haut-parleurs
Énergie de sortie 250 mW

ModesdEmploi.fr

Vous cherchez un manuel ? ModesdEmploi.fr vous permet de trouver le manuel que vous recherchez en un rien de temps. Notre base de données contient plus d'un million de manuels en PDF pour plus de 10 000 marques. Chaque jour, nous ajoutons les derniers manuels afin que vous trouviez toujours le produit que vous recherchez. C'est très simple : entrez le nom de la marque et le type de produit dans la barre de recherche pour consulter gratuitement et immédiatement le manuel de votre choix en ligne.

ModesdEmploi.fr

© Copyright 2020 ModesdEmploi.fr. Tous droits réservés.

Nous utilisons des cookies pour vous garantir la meilleure expérience sur notre site. Si vous continuez à utiliser ce dernier, nous considérerons que vous acceptez l'utilisation des cookies.

En savoir plus