Sony MDR-RF855RK mode d'emploi

Sony MDR-RF855RK
5.2 · 1
PDF mode d'emploi
 · 2 pages
Français
mode d'emploiSony MDR-RF855RK

Wireless Stereo

Headphone System

©2012 Sony Corporation Printed in China4-441-668-16(1)MDR-RF855RKEnglish Wireless Stereo Headphone System
WARNING
To reduce the risk of fire or electric shock, do not expose this
apparatus to rain or moisture.
To reduce the risk of fire or electric shock, do not expose this
apparatus to dripping or splashing, and do not place objects
filled with liquids, such as vases, on the apparatus.
To avoid electrical shock, do not open the cabinet. Refer
servicing to qualified personnel only.
Do not install the appliance in a confined space, such as a
bookcase or built-in cabinet.
As the main plug of AC power adaptor is used to disconnect the
AC power adaptor from the mains, connect it to an easily
accessible AC outlet. Should you notice an abnormality in it,
disconnect it from the AC outlet immediately.
CAUTION
Risk of explosion if the battery is replaced by an incorrect type.
Do not expose the batteries (battery pack or batteries installed)
to excessive heat such as sunshine, fire or the like for a long time.
Do not subject the batteries to extreme low temperature
conditions that may result in overheating and thermal runaway.
Do not dismantle, open or shred secondary cells or batteries.
Do not expose cells or batteries to heat or fire. Avoid storage in
direct sunlight.
In the event of a cell leaking, do not allow the liquid to come in
contact with the skin or eyes. If contact has been made, wash the
affected area with copious amounts of water and seek medical
advice.
Do not use any charger other than that specifically provided for
use with the equipment.
Secondary cells and batteries need to be charged before use.
Always use the correct charger and refer to the manufacturers
instructions or equipment manual for proper charging
instructions.
After extended periods of storage, it may be necessary to charge
and discharge the cells or batteries several times to obtain
maximum performance.
Dispose of properly.
High volume may affect your hearing.
The nameplate of transmitter is located on the bottom exterior.
The validity of the CE marking is restricted to only those
countries where it is legally enforced, mainly in the countries EEA
(European Economic Area) and Switzerland.
Hereby, Sony Corporation declares that this equipment is in
compliance with Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at
the following internet address:
http://www.compliance.sony.de/
Disposal of waste batteries and electrical
and electronic equipment (applicable in the
European Union and other countries with
separate collection systems)
This symbol on the product, the battery or on
the packaging indicates that the product and
the battery shall not be treated as household waste. On certain
batteries this symbol might be used in combination with a
chemical symbol. The chemical symbol for lead (Pb) is added if
the battery contains more than 0.004% lead. By ensuring that
these products and batteries are disposed of correctly, you will
help to prevent potentially negative consequences for the
environment and human health which could be caused by
inappropriate waste handling. The recycling of the materials will
help to conserve natural resources.
In case of products that for safety, performance or data integrity
reasons require a permanent connection with an incorporated
battery, this battery should be replaced by qualified service staff
only. To ensure that the battery and the electrical and electronic
equipment will be treated properly, hand over these products at
end-of-life to the appropriate collection point for the recycling of
electrical and electronic equipment. For all other batteries,
please view the section on how to remove the battery from the
product safely. Hand the battery over to the appropriate
collection point for the recycling of waste batteries. For more
detailed information about recycling of this product or battery,
please contact your local Civic Office, your household waste
disposal service or the shop where you purchased the product
or battery.
Notice for customers: the following information is only
applicable to equipment sold in countries applying EU
directives
This product has been manufactured by or on behalf of Sony
Corporation.
EU Importer: Sony Europe B.V.
Inquiries to the EU Importer or related to product compliance in
Europe should be sent to the manufacturer’s authorized
representative, Sony Belgium, bijkantoor van Sony Europe B.V.,
Da Vincilaan 7-D1, 1930 Zaventem, Belgium.
This equipment has been tested and found to comply with the
limits set out in the EMC regulation using a connection cable
shorter than 3 meters.
The unit is not waterproof. If water or foreign objects enter the
unit, it may result in fire or electric shock. If water or a foreign
object enters the unit, stop use immediately and consult your
nearest Sony dealer. In particular, be careful in the following
cases.
When using the unit around a sink, etc.
Be careful that the unit does not fall into a sink or container
filled with water.
When using the unit in the rain or snow, or in humid locations
When using the unit while you are sweaty
If you touch the unit with wet hands, or put the unit in the
pocket of a damp article of clothing, the unit may get wet.
Note on static electricity
Static electricity accumulated in the body may cause mild
tingling in your ears. To reduce the effect, wear clothes made
from natural materials, which suppress the generation of static
electricity.

How to use

After use
The headphones automatically turn off when they are taken
off (Auto power on/off function).
About auto power on/off function
When you put on the headphones, the headphones' power
turns on automatically. Wear the headphones vertically on
your head so that auto power on function is properly
activated.
The headphones automatically turn off when they are taken
off.
Do not pull up the self-adjusting band when not in use, this
will consume the battery power.
Self-adjusting band
About sending RF signals
The transmitter starts sending RF signals automatically when
it detects an audio signal from the connected component.
Note that;
Noise may occur depending on the transmitter position and
room conditions. It is recommended to place the
transmitter in a location that produces the clearest sound.
If the transmitter is placed on a metallic table, you may hear
noise, or the reception range may decrease. Do not place on
a metallic table.
If low signal or no signal is input for
about 5 minutes
If low signal is input for about 5 minutes, the transmitter turns
off automatically*. If the volume of the connected A/V
component is too low, the transmitter may also turn off. When
low signal is input, the POWER/GREEN indicator of the
transmitter flashes green for 5 minutes, then turns off. In this
case, raise the volume of the connected A/V component
within the range where the sound is not distorted, then lower
the volume of the headphones.
The transmitter may also turn off if no signal is input for about
5 minutes. The POWER/GREEN indicator of the transmitter
flashes green for 5 minutes, then turns off. The transmitter
restarts after receiving an audio signal again.
* If signal noise is output from the connected A/V
component, the transmitter may not turn off, even when no
audio signal is input.
Tips for charging
Charge supplied battery first
The supplied rechargeable nickel-metal hydride battery is not
charged from the first time you use it. Be sure to charge them
before use.
About auto charge function
Placing the headphones on the transmitter automatically turns
them off, then charging starts. This eliminates the need for
turning on/off every time you wear and take off the headphones.
If CHG/RED indicator does not light up
red
Check if the right and left headphones are rested on the
transmitter correctly. Take off the headphones and place them
on the transmitter again so that the headphones’ contact
points meet the transmitter’s contact pins.
Charging may not be completed if the transmitters contact
pin and headphones’ contact point are dusty. Wipe them with
a cotton bud, etc.
Charging and usage time
Depending on the remaining battery status, it takes approx. 30
minutes to 7 hours to recharge.
Approx. charging time Approx. usage time
1)
7 hours
2)
18 hours
3)
1) at 1 kHz, 0.1 mW + 0.1 mW output
2) hours required to fully charge an empty battery
3) Time may vary, depending on the temperature or conditions
of use.
To recharge supplied battery after use
Place the headphones on the transmitter after use. The CHG/RED
indicator lights up red, then charging starts.
When charging is complete, there is no need to remove the
headphones from the transmitter.
Remaining battery
To check the remaining battery charge of the headphones, pull
up the self-adjusting band, and check the POWER indicator. The
battery is still serviceable when the indicator lights up green.
Charge the headphones if the POWER indicator turns off, dims,
flashes, or the sound becomes distorted or noisy.
Notes
Insert the AC adaptor plug firmly.
Be sure to use the supplied AC adaptor. Using AC adaptors
with different plug polarity or other characteristics can cause
product failure.
Unified
polarity plug
The battery capacity may decrease if the headphones are
turned on and placed on the transmitter with the AC adaptor
disconnected.
The transmitter automatically turns off while charging the
battery.
This system is designed to charge only the supplied
rechargeable battery BP-HP550-11 for safety. Note that other
types of rechargeable battery cannot be charged with this
system.
If dry batteries are installed, they cannot be charged.
Do not attempt to use the supplied rechargeable battery BP-
HP550-11 for other components. It is for use with this system
only.
Charge in an environmental temperature of between 5 °C and
35 °C (between 41 °F and 95 °F).
When the battery life reduces to half, this may be the end of
battery lifetime. The supplied rechargeable battery BP-HP550-
11 is not commercially available. You can order the battery
from the store where you purchased this system, or at your
nearest Sony dealer.
Using the headphones
with separately-sold dry
batteries
Commercially available (LR03 (size AAA)) dry batteries can also
be used to power the headphones. Install two batteries in the
same manner as described in step 1 of “How to use.
When dry batteries are installed, the battery charge function is
not activated.
Battery life
Battery Approx. usage time
1)
Sony alkaline battery LR03
(size AAA)
28 hours
2)
1) at 1 kHz, 0.1 mW + 0.1 mW output
2) Time may vary, depending on the temperature or conditions
of use.
Note
Do not carry a dry battery together with coins or other metallic
objects. It can generate heat if the positive and negative
terminals of the battery are accidentally come into contact with
metallic objects.
Tips for connection
Do not connect to the AUDIO IN 1 and AUDIO IN 2 jacks at the
same time. If you connect two A/V components to both jacks
at the same time, both of the audio signals may result in mixed
output.
When you connect the connecting cable directly to an
earphone jack (monaural mini jack), the audio signal may not
be output through the right channel.
Tips for volume setting
If you connect the transmitter to the headphone jack of the A/
V component, set the volume of the A/V component as high as
possible but not so high that the audio signal becomes
distorted.
When watching videos, be careful not to raise the volume too
high in quiet scenes. You may hurt your ears when a loud
scene is played.
Tips for better reception
Receiving performance
This system utilizes very high frequency signals in the 800 MHz
band so the receiving performance may deteriorate due to the
surroundings. The following examples illustrate conditions that
may reduce the reception range or cause interference.
Inside a building with walls containing steel beams
An area with many steel file cabinets, etc.
An area with many electrical appliances capable of generating
electromagnetic fields
The transmitter is placed on a metal instrument.
An area facing a roadway
Noise or interfering signals exist in the surroundings due to
radio transceivers in trucks, etc.
Noise or interfering signals exist in the surroundings owing to
wireless communication systems installed along roadways.
Effective area of the transmitter
The optimum distance is up to approximately 100 m without the
system picking up some interference. However, the distance may
vary depending on the surroundings and environment.
If the system picks up some noise within the above mentioned
distance, reduce the distance between the transmitter and the
headphones, or select another channel.
When you use the headphones inside the effective area of the
transmitter, the transmitter can be placed in any direction from
the listener.
Even within the signal reception area, there are some spots
(dead spots) where the RF signal cannot be received. This
characteristic is inherent to RF signals, and does not indicate
malfunction. By slightly moving the transmitter, location of the
dead spot can be changed.
Replacing the earpads
The earpads are replaceable. If the earpads become dirty or
worn out, replace them as illustrated below. The earpads are not
commercially available. You can order replacements from the
store where you purchased this system, or at your nearest Sony
dealer.
1 Remove the old earpad by pulling it out of the groove on the
housing.
2 Place the new earpad on the driver unit.
Hang the edge of the earpad on one side of the driver unit’s
groove edge, then turn the edge of earpad around the driver
unit as illustrated below.
When the earpad is securely inserted into the groove, adjust
the earpad to the vertical position.
Troubleshooting
If you run into any problems using this system, use the following
checklist. Should any problem persist, consult your nearest Sony
dealer.
No sound/Low sound
Check the connection of the A/V component or the AC
adaptor.
Check that the A/V component is turned on.
If you connect the transmitter to an A/V component using the
headphone jack, raise the volume level on the connected A/V
component within the range where the sound is not distorted.
Change the radio frequency with the CHANNEL selector on the
transmitter, then change the radio frequency to that of the
transmitter with the TUNING switch on the headphones.
Use the headphones near the transmitter, or change the
position of the transmitter.
Charge the supplied rechargeable battery, or replace dry
batteries with new ones. If the POWER indicator is still off after
charging, take the headphones to a Sony dealer.
Raise the headphone volume.
Distorted or intermittent sound (sometimes with noise)
Use the headphones near the transmitter, or change the
position of the transmitter.
Do not place the transmitter on a metallic table.
If you connect the transmitter to an A/V component using the
headphone jack, lower the volume level on the connected A/V
component within the range where the sound is not distorted.
Change the radio frequency with the CHANNEL selector on the
transmitter, then change the radio frequency to that of the
transmitter with the TUNING switch on the headphones.
Charge the supplied rechargeable battery, or replace dry
batteries with new ones. If the POWER indicator is still off after
charging, take the headphones to a Sony dealer.
Loud background noise
If you connect the transmitter to an A/V component using the
headphone jack, raise the volume level on the connected A/V
component within the range where the sound is not distorted.
Charge the supplied rechargeable battery, or replace dry
batteries with new ones. If the POWER indicator is still off after
charging, take the headphones to a Sony dealer.
Do not place the transmitter on a metallic table.
Use the headphones near the transmitter.
The POWER/GREEN indicator flashes green
No signal or low signal is input. Start playback of the A/V
component, or raise the volume of the connected A/V
component within the range where the sound is not distorted,
otherwise the transmitter will turn off. If no signal or low signal
is input for about 5 minutes, the transmitter turns off
automatically.
The sound cuts off
The transmitter turns off if no signal or low signal is input for
5 minutes. If you connect the transmitter to an A/V component
using the headphone jack, raise the volume level on the
connected A/V component within the range where the sound
is not distorted.
Battery cannot be charged/ CHG/RED indicator flashes red, or does not light up red
Check that the right/left of the headphones and transmitter
correspond, and put the headphones on the transmitter
correctly.
Install the supplied rechargeable nickel-metal hydride battery.
Dry batteries and rechargeable batteries other than the
supplied cannot be charged.
If the CHG/RED indicator does not light up red even though
you put the headphones on the transmitter and wait for a
while, it may be the end of battery lifetime. You can order the
supplied rechargeable battery BP-HP550-11 from the store
where you purchased this system, or at your nearest Sony
dealer.
Charging may not be completed if the transmitters contact
pin and headphones’ contact point are dusty. Wipe them with
a cotton bud, etc.
Precautions
When this system is not to be used for a long period of time,
disconnect the AC adaptor from the AC outlet holding the
plug, and remove the battery from the headphones to avoid
damage caused by battery leakage and subsequent corrosion.
Do not leave this system in a location subject to direct
sunlight, heat or moisture.
You may hear some noise when you disconnect the AC
adaptor from the transmitter before taking off the
headphones.
Avoid exposure to temperature extremes, direct sunlight,
moisture, sand, dust or mechanical shock.
Notes on headphonesTo reduce the risk of hearing damage
Avoid using headphones at high volume. Hearing experts advise
against continuous, loud and extended play. If you experience a
ringing in your ears, lower the volume or discontinue use.
Caring for others
Keep the volume at a moderate level. This will allow you to hear
outside sounds and to be considerate to the people around you.
If you have any questions or problems concerning the system
that are not covered in this manual, please consult your nearest
Sony dealer.
Be sure to bring the headphones and the transmitter to the Sony
dealer when requiring repair work.
Specifications
RF stereo transmitter (TMR-RF855R)
Modulation FM stereo
Operating frequency
863.0 MHz – 865.0 MHz
Maximum output power
< 4 mW
Channel Ch1, Ch2, Ch3
Transmission distance
Approx. 100 m of longest
Audio inputs Pin jacks (left/right)
Stereo mini jack
Power requirements
DC 12 V (from the supplied AC adaptor)
Dimensions Approx. 180 mm × 94 mm × 126 mm (w/h/d)
Mass Approx. 310 g
Rated power consumption
3.0 W
Operating temperature
5°C to 35°C (41°F to 95°F)
Wireless stereo headphones (MDR-RF855R)
Frequency response
10 Hz – 22,000 Hz
Power source Supplied rechargeable nickel-metal hydride
battery BP-HP550-11, or commercially
available (LR03 (size AAA)) dry batteries
Mass Approx. 280 g including battery
Operating temperature
5°C to 35°C (41°F to 95°F)
Connect the AC adaptor.
Insert the plug firmly.
Charge the headphones.
To AC
outlet
(Red) (Off)
Complete when
indicator turns off.
Connect the A/V component, following hookup or below.
Insert the plug firmly.
Using the headphone jack of the A/V component
L (white)R (red)
Stereo mini plug
Headphone jack
(Stereo mini jack)
TV, Digital music player, etc.
L (white)
R (red)
Stereo mini plug
Audio out
(L/R) jacks
Stereo system, Blu-ray Disc player,
DVD player, etc.
Start playback of the A/V component.
The POWER/GREEN indicator of the transmitter lights up green.
Wear the headphones.
Before listening
To reduce the risk of hearing damage, first lower the volume.
Using the audio out (L/R) jacks of the A/V component
Insert the supplied rechargeable battery BP-HP550-11 into the left housing of the headphones.
Observe the correct polarity when installing battery.
Contact
pins
Rechargeable nickel-metal hydride
battery BP-HP550-11 (supplied)
Contact
points
Tactile dot
Insert the
end first.
Operating InstructionsMode d’emploi
Checking the included
items
Transmitter TMR-RF855R (1)
AC adaptor (1)
Rechargeable nickel-metal
hydride battery
(BP-HP550-11) (1)
Headphones MDR-RF855R (1)
Connecting cable (stereo mini
plug pin plug × 2), 1 m (1)
Features
Thank you for purchasing the Sony MDR-RF855RK Wireless
Stereo Headphone System. Before operating the unit, please
read this manual thoroughly and retain it for future reference.
Some features are:
Wireless headphone system with long battery life and 100 m
range
Hassle-free recharging by placing the headphones on the
transmitter
40 mm driver units for deep bass response
Auto power on/off function for longer battery life
Battery playback time up to 18 hrs with rechargeable batteries
or 28 hrs with Sony alkaline batteries
Lock Release
Adjust the volume.
Up
Down
Tactile dot
If you cannot receive a clear audio signal
First change the radio frequency with the CHANNEL selector switch on the transmitter,
then change the radio frequency to that of the transmitter with the TUNING switch on
the headphones.
(Green)
Svenska
Härmed försäkrar Sony Corporation att denna utrustning
överensstämmer med direktiv 2014/53/EU.
Den fullständiga texten till EU-försäkran om överensstämmelse
finns på följande webbadress:
http://www.compliance.sony.de/
Dansk
Herved erklærer Sony Corporation, at dette udstyr er i
overensstemmelse med direktiv 2014/53/EU.
Den fulde ordlyd af EU-overensstemmelseserklæringen er
tilgængelig på følgende internetadresse:
http://www.compliance.sony.de/
Suomi
Sony Corporation vakuuttaa, että tämä laite on direktiivin
2014/53/EU mukainen.
EU-vaatimustenmukaisuusvakuutuksen täysimittainen teksti on
saatavilla seuraavassa internetosoitteessa:
http://www.compliance.sony.de/
Norsk
Herved erklærer Sony Corporation at utstyrstypen er i samsvar
med direktiv 2014/53/EU.
EU-erklæring fulltekst finner du på Internett under:
http://www.compliance.sony.de/
Français
Le soussigné, Sony Corporation, déclare que cet équipement est
conforme à la Directive 2014/53/UE.
Le texte complet de la déclaration UE de conformité est
disponible à l’adresse internet suivante :
http://www.compliance.sony.de/
Deutsch
Hiermit erklärt Sony Corporation, dass diese Funkanlage der
Richtlinie 2014/53/EU entspricht.
Der vollständige Text der EU-Konformitätserklärung ist unter der
folgenden Internetadresse verfügbar:
http://www.compliance.sony.de/
Español
Por la presente, Sony Corporation declara que este equipo es
conforme con la Directiva 2014/53/UE.
El texto completo de la declaración UE de conformidad está
disponible en la dirección Internet siguiente:
http://www.compliance.sony.de/
Nederlands
Hierbij verklaart Sony Corporation dat deze radioapparatuur
conform is met Richtlijn 2014/53/EU.
De volledige tekst van de EU-conformiteitsverklaring kan
worden geraadpleegd op het volgende internetadres:
http://www.compliance.sony.de/
Italiano
Con la presente, Sony Corporation dichiara che questo
apparecchio è conforme alla Direttiva 2014/53/UE.
Il testo completo della dichiarazione di conformità UE è
disponibile al seguente indirizzo Internet:
http://www.compliance.sony.de/
Português
O(a) abaixo assinado(a) Sony Corporation declara que o presente
equipamento está em conformidade com a Diretiva 2014/53/UE.
O texto integral da declaração de conformidade está disponível
no seguinte endereço de Internet:
http://www.compliance.sony.de/
Slovensky
Sony Corporation týmto vyhlasuje, že zariadenie je v súlade so
smernicou 2014/53/EÚ.
Úplné vyhlásenie EÚ o zhode je k dispozícii na tejto internetovej
adrese:
http://www.compliance.sony.de/
Slovenščina
Sony Corporation potrjuje, da je ta oprema skladna z Direktivo
2014/53/EU.
Celotno besedilo izjave EU o skladnosti je na voljo na naslednjem
spletnem naslovu:
http://www.compliance.sony.de/
Česky
Sony Corporation tímto prohlašuje, že toto zařízení je v souladu
se směrnicí 2014/53/EU.
Úplné znění EU prohlášení o shodě je k dispozici na této
internetové adrese:
http://www.compliance.sony.de/
Magyar
A Sony Corporation igazolja, hogy ez a készülék megfelel a
2014/53/EU irányelvnek.
Az EU-megfelelőségi nyilatkozat teljes szövege elérhető a
következő internetes címen:
http://www.compliance.sony.de/
Български
С настоящото, Sony Corporation декларира, че това
оборудване е в съответствие с Директива 2014/53/EU.
Цялостният текст на ЕС декларацията за съответствие може
да се намери на следния интернет адрес:
http://www.compliance.sony.de/
Polski
Sony Corporation niniejszym oświadcza, że to urządzenie jest
zgodne z dyrektywą 2014/53/UE.
Pełny tekst deklaracji zgodności UE jest dostępny pod
następującym adresem internetowym:
http://www.compliance.sony.de/
Română
Prin prezenta, Sony Corporation declară că acest echipament
este în conformitate cu Directiva 2014/53/UE.
Textul integral al declarației UE de conformitate este disponibil la
următoarea adresă internet:
http://www.compliance.sony.de/
Included items
RF stereo transmitter TMR-RF855R
Wireless stereo headphones MDR-RF855R
AC adaptor (12 V) (1)
Connecting cable (stereo mini plug pin plug × 2), 1 m (1)
Rechargeable nickel-metal hydride battery BP-HP550-11
(550 mAh min) (1)
Card warranty (1)
Operating Instructions (this manual) (1)
Design and specifications are subject to change without notice.
For details on the effect of contact to the human body from the
mobile phone or other wireless devices connected to the unit,
refer to the instruction manual of the wireless device.
This product (including accessories) has magnet(s) which may
interfere with pacemakers, programmable shunt valves for
hydrocephalus treatment, or other medical devices. Do not place
this product close to persons who use such medical devices.
Consult your doctor before using this product if you use any
such medical device.
4
2
5
6
1
3
7

Mode d'emploi

Consultez gratuitement le manuel de la marque Sony MDR-RF855RK ici. Ce manuel appartient à la catégorie Écouteurs et a été évalué par 1 personnes avec une moyenne de 5.2. Ce manuel est disponible dans les langues suivantes: Français, Anglais. Vous avez une question sur le MDR-RF855RK de la marque Sony ou avez-vous besoin d’aide? Posez votre question ici

Besoin d’aide?

Vous avez une question sur le Sony MDR-RF855RK et la réponse n'est pas dans le manuel? Posez votre question ici. Fournissez une description claire et complète du problème, et de votre question. Plus votre problème et votre question sont clairement énoncés, plus les autres propriétaires de Sony MDR-RF855RK ont de chances de vous fournir une bonne réponse.

Verbois • 3-7-2022 Pas de commentaire

Comment insérer la pile regarchable. Nous n arrivons pas à dévisser l oreillette

Répondez à cette question
Sacco • 30-6-2022 Pas de commentaire

Je viens d’acheter ce casque Sony, il a marché 4 jours, puis fini. J’ai acheté une nouvelle batterie chez Sony ç ne marche toujours pas

Répondez à cette question
MERCIER • 19-4-2022 Pas de commentaire

J AI INSTALLE MON CASQUE TV SANS SONY IMPOSSIBLE DE RESEVOIR DE SON JAI MIS LE VOLUME

Répondez à cette question
MERCIER • 19-4-2022 1 commentaire

pas de son sur les ecouteurs

Sacco • 30-6-2022

Pas de son c’est mon deuxième cas identique et c’est de la mer

Répondez à cette question

Nombre de questions : 4

Spécifications du MDR-RF855RK de la marque Sony

Vous trouverez ci-dessous les spécifications du produit et les spécifications du manuel du Sony MDR-RF855RK.

Généralités
Marque Sony
Modèle MDR-RF855RK | MDRRF855RK
Produit écouteur
EAN 4901780536306, 4905524858570, 0490552485675, 4905524858679
Langue Français, Anglais
Type de fichier Mode d’emploi (PDF)
Batterie
Autonomie maximum de la batterie 18 h
Temps de rechargement de la batterie 7 h
Technologie batterie Hybrides nickel-métal (NiMH)
Indicateur de chargement Oui
Batterie rechargeable Oui
Casques/Ecouteurs
Unité de lecture 40 mm
Type d'aimant Néodyme
DHT, distorsion harmonique totale 2 %
Fréquence des écouteurs 10 - 22000 Hz
Couplage auriculaire Circum-aural
Autres caractéristiques
Type de bandes supportées FM
Poids du transmetteur 300 g
Connectivité
Portée du routeur sans fil 100 m
Technologie de connectivité Sans fil
Connectivité RF Oui
Poids et dimensions
Poids 285 g
représentation / réalisation
Couleur du produit Noir
Style de casque portable Arceau
Type de produit Écouteurs
Utilisation recommandée Musique
Microphone
Type de microphone Indisponible
Données logistiques
Code du système harmonisé 85183000
voir plus

Foire aux questions

Vous ne trouvez pas la réponse à votre question dans le manuel? Vous trouverez peut-être la réponse à votre question dans la FAQ sur le Sony MDR-RF855RK au dessous de.

Votre question n'est pas dans la liste ? Posez votre question ici

Aucun résultat