Sony MDR-RF865RK mode d'emploi

Sony MDR-RF865RK
7.4 · 1
PDF mode d'emploi
 · 2 pages
Français
mode d'emploiSony MDR-RF865RK
Connection

Setting up the transmitter

1 Connect the transmitter to an AV component.
Select one of the hookups below depending on the jack
type:
To connect to the headphone jack of the connected
equipment
Insert the plug firmly
Transmitter
Left channel
(white)
Right channel
(red)
To AUDIO IN 1
jacks
Connecting cord
(supplied)
To headphones jack
(Stereo mini jack)
WALKMAN*,
TV, etc.
To connect to the LINE OUT or REC OUT jack of
the connected equipment
Insert the plug firmly
Transmitter
To AUDIO IN 2
jack
Right channel (red)
Connecting cord
(supplied)
Stereo system,
Blu‑ray Disc player,
DVD player, etc.
To LINE OUT or
REC OUT jacks
Left channel (white)
Operation

Listening to a programme

Before listening
To reduce the risk of hearing damage, first lower the volume.
1 Turn on the AV component connected to the
transmitter.
If the transmitter is connected to the headphone jack, set
the volume control of the audio source component as
high possible but not so high that the audio signal
becomes distorted.
2 Remove the headphones from the transmitter.
The transmitter’s POWER indicator lights up in green.
Disposal of waste batteries (applicable
in the European Union and other
European countries with separate
collection systems)
This symbol on the battery or on the
packaging indicates that the battery provided with this
product shall not be treated as household waste.
On certain batteries this symbol might be used in
combination with a chemical symbol. The chemical symbols
for mercury (Hg) or lead (Pb) are added if the battery
contains more than 0.0005% mercury or 0.004% lead.
By ensuring these batteries are disposed of correctly, you
will help prevent potentially negative consequences for the
environment and human health which could otherwise be
caused by inappropriate waste handling of the battery. The
recycling of the materials will help to conserve natural
resources.
In case of products that for safety, performance or data
integrity reasons require a permanent connection with an
incorporated battery, this battery should be replaced by
qualified service staff only.
To ensure that the battery will be treated properly, hand over
the product at end-of-life to the applicable collection point
for the recycling of electrical and electronic equipment.
For all other batteries, please view the section on how to
remove the battery from the product safely. Hand the battery
over to the applicable collection point for the recycling of
waste batteries.
For more detailed information about recycling of this
product or battery, please contact your local Civic Office,
your household waste disposal service or the shop where
you purchased the product.
Notice for customers: the following information is only
applicable to equipment sold in countries applying EU
directives
This product has been manufactured by or on behalf of Sony
Corporation, 1-7-1 Konan Minato-ku Tokyo, 108-0075
Japan. Inquiries related to product compliance based on
European Union legislation shall be addressed to the
authorized representative, Sony Belgium, bijkantoor van
Sony Europe Limited, Da Vincilaan 7-D1, 1935 Zaventem,
Belgium. For any service or guarantee matters, please refer
to the addresses provided in the separate service or
guarantee documents.

The effective areas of the

transmitter

The optimum distance is up to approximately 100 m without
the system picking up some interference. However, the
distance may vary depending on the surroundings and
environment. If the system picks up some noise within the
above mentioned distance, reduce the distance between the
transmitter unit and the headphones, or select another
channel.
Notes
When you use the headphones inside the effective areas of the
transmitter, the transmitter can be placed in any direction from the
listener.
Even within the signal reception area, there are some spots (dead
spots) where the RF signal cannot be received. This characteristics
is inherent to RF signals, and does not indicate malfunction. By
slightly moving the transmitter, location of the dead spot can be
changed.

Checking the remaining

battery power

Turn on the switch located on the left housing of the
headphone, and check the POWER indicator located on the
left housing. The battery are still serviceable when the
indicator lights up green.
Charge the rechargeable battery if the POWER indicator
light dims, flashes, or the sound becomes distorted or noisy.

Replacing the earpads

The earpads are replaceable. If the earpads become dirty or
worn out, replace them as illustrated below. The earpads are
not commercially available. You can order replacements
from the store where you purchased this system, or at your
nearest Sony dealer.
1 Remove the old earpad by pulling it out of the
groove on the housing.
2 Place the new earpad on the driver unit.
Hang the edge of the earpad on one side of the driver
units groove edge, then turn the edge of earpad around
the driver unit as illustrated below.
When the earpad is securely inserted into the groove,
adjust the earpad to the vertical position.
Additional information

Troubleshooting

If you run into any problems using this headphone system,
use the following checklist. Should any problem persist,
consult your nearest Sony dealer.
No sound
Check the connection of the audio/video equipment or the AC
power adaptor.
Check that the audio/video equipment is turned on.
Turn up the volume on the connected audio/video equipment
within the range where the sound is not distorted, if the
transmitter is connected to the headphones jack.
Change the radio frequency with the CHANNEL selector on the
transmitter, then press the AUTO TUNING button on the right
housing of the headphones.
The mute function is activated.
Use the headphones near the transmitter.
Change the position of the transmitter.
The headphones’ POWER indicator light turns off, dims, flashes,
or sound becomes distorted or noisy.
Charge the rechargeable battery. If the POWER indicator is still
off after charging the battery, take the headphones to a Sony
dealer.
Distorted or intermittent sound (sometimes with noise)
Charge the rechargeable battery. If the POWER indicator is still
off after charging the battery, take the headphones to a Sony
dealer.
Change the position of the transmitter.
Do not place the transmitter on a metallic table.
If you connect the transmitter to an AV component using the
headphone jack, lower the volume level on the connected AV
component within the range where the sound is not distorted.
Change the radio frequency with the CHANNEL selector switch
on the transmitter, then set to the same radio frequency with the
AUTO TUNING button on the right housing of the headphones.
Use the headphones near the transmitter.
Low sound
If you connect the transmitter to an AV component using the
headphone jack, raise the volume level on the connected AV
component within the range where the sound is not distorted.
Raise the headphone volume.
Loud background noise
If you connect the transmitter to an AV component using the
headphone jack, raise the volume level on the connected AV
component within the range where the sound is not distorted.
Charge the rechargeable battery. If the POWER indicator is still
off after charging the battery, take the headphones to a Sony
dealer.
Do not place the transmitter on a metallic table.
Use the headphones near the transmitter.

Welcome!

Thank you for purchasing the Sony MDR-RF865RK Wireless
Stereo Headphone System. Before operating the unit, please
read this manual thoroughly and retain it for future reference.
Some features are:
Wireless system that allows you to listen to a programme
free from the restriction of a cord
Easy connection to TV and HiFi Audio system equipment
Fast recharging function with secure charging mechanism
Noise reduction system to reproduce a clear sound with
minimum transmission noise
Automatic tuning on headphones for optimum signal
reception
3 transmission channels available
Up to 100 meters reception range*
Long playback time (approx. 25 hours)
High fidelity sound reproduction
Volume control function on the headphones
* Transmission distance varies depending on conditions of use.

Notes on receiving

performance

This system utilises very high frequency signals in the 800
MHz band so the receiving performance may deteriorate
due to the surroundings. The following examples illustrate
conditions that may reduce the reception range or cause
interference.
Inside a building with walls containing steel beams
An area with many steel file cabinets, etc.
An area with many electrical appliances capable of
generating electromagnetic fields
The transmitter is placed on a metal instrument.
An area facing a roadway
Noise or interfering signals exist in the surroundings due
to radio transceivers in trucks, etc.
Noise or interfering signals exist in the surroundings
owing to wireless communication systems installed along
roadways.
Preparation

Checking the components and

accessories

Before setting up the system, check that all of the
components are included.
RF stereo transmitter TMR-RF865R (1)
Wireless stereo headphones MDR-RF865R (1)
AC power adaptor (1)
Connecting cable (stereo mini plug
pin plug × 2), 1 m (1)

English

WARNING

To reduce the risk of fire or electric shock, do not expose
this apparatus to dripping or splashing, and do not place
objects filled with liquids, such as vases, on the apparatus.
Do not expose the batteries (battery pack or batteries
installed) to excessive heat such as sunshine, fire or the like
for a long time.
To avoid electrical shock, do not open the cabinet. Refer
servicing to qualified personnel only.
Do not install the appliance in a confined space, such as a
bookcase or built-in cabinet.
As the main plug of AC power adaptor is used to disconnect
the AC power adaptor from the mains, connect it to an
easily accessible AC outlet. Should you notice an
abnormality in it, disconnect it from the AC outlet
immediately.
Excessive sound pressure from earphones and headphones
can cause hearing loss.
The nameplate is located on the bottom exterior.
The validity of the CE marking is restricted to only those
countries where it is legally enforced, mainly in the
countries EEA (European Economic Area).
Hereby, Sony Corp., declares that this equipment is in
compliance with the essential requirements and other
relevant provisions of Directive 1999/5/EC.
For details, please access the following URL :
http://www.compliance.sony.de/
Disposal of Old Electrical & Electronic
Equipment (Applicable in the European
Union and other European countries
with separate collection systems)
This symbol on the product or on its
packaging indicates that this product shall
not be treated as household waste. Instead it
shall be handed over to the applicable collection point for
the recycling of electrical and electronic equipment. By
ensuring this product is disposed of correctly, you will help
prevent potential negative consequences for the
environment and human health, which could otherwise be
caused by inappropriate waste handling of this product. The
recycling of materials will help to conserve natural
resources. For more detailed information about recycling of
this product, please contact your local Civic Office, your
household waste disposal service or the shop where you
purchased the product.
3 Select the radio frequency with the CHANNEL
selector switch.
4 Turn on the switch on the left housing of the
headphones.
Check if the power indicator on the left housing lights
up green. Adjust the headband of the headphones, and
place the right housing on your right ear and the left
housing on your left ear.
There is a tactile dot on the hanger marked to
distinguish the left side.
Tactile dot
5 Set the channel to that of the transmitter with the
button on the right housing of the headphones.
Press the AUTO TUNING button briefly for automatic
tuning of the headphones. If you do not receive a clear
audio signal or changed the CHANNEL selector switch
on the transmitter, press it again.
When tuning has completed, turn up the volume to a
moderate level with the VOL control on the right
housing. Turn the VOL control towards the dot to turn
up the volume.
Tactile dot
Notes
When watching films, be careful not to raise the volume too
high in quiet scenes. You may hurt your ears when a loud scene
is played.
This equipment is guaranteed for use in the temperature range
of 5°C to 35°C (41°F to 95°F).
You may hear some noise when you disconnect the AC power
adaptor from the transmitter before removing the headphones.
After use
Turn off the power of the headphones.
Note
Note that battery capacity may decrease if the headphones are turned
on and placed on the transmitter with the AC power adaptor
disconnected from the transmitter.
Sending RF signals from the transmitter
The transmitter starts sending RF signals automatically
when it detects an audio signal from the connected
equipment.
Notes
Any noise you hear through the headphones may vary depending
on the transmitter position and room conditions. It is
recommended that you place the transmitter in a location that
produces the clearest sound.
If the transmitter is placed on a metallic table, you may hear noise,
or the reception range may decrease.
Do not place the transmitter on a metallic table.
If an audio signal is not input for about 5 minutes
RF signal transmission from the transmitter automatically
stops when an audio signal is not input for about 5 minutes.
When the transmitter stops, the transmitters POWER
indicator blinks in green for 60 seconds and then turns off.
The RF signals are automatically transmitted when an audio
signal is input again. RF signal transmission may stop when
an extremely low sound is input for about 5 minutes. If this
happens, raise the volume of the connected AV component
within the range where the sound is not distorted, and lower
the volume of the headphones.
If signal noise is output from a component connected to the
AUDIO IN jacks, RF signal transmission may not stop.
Noise Reduction process
The transmitter unit compresses the audio signal and
converts it to RF signal. The headphones unit converts the
received RF signal to an audio signal and decompresses it.
This process reduces noise picked up during transmission.
input signal
output signal
decompression
compression
dynamic range
Transmitter unit Headphones unit
RF transmission
noise level (low)
 
The transmitter unit compresses the audio signals
dynamic range, then converts it to RF signal.
Noise may occur due to long distance transmission, etc.
The headphones unit converts the RF signal to an audio
signal.
Noise may occur during conversion.
Decompression of the audio signals dynamic range
reduces the noise level and improves the S/N (signal-to-
noise) ratio.

Charging

1 Connect the supplied AC power adaptor to the
transmitter.
Transmitter
AC power adaptor
(supplied)
To an AC outlet
To DC IN
12 V jack
Notes
Insert the plug firmly.
Be sure to use the supplied AC power adaptor. Using AC
adaptors with different plug polarity or other characteristics
can cause product failure.
Unified polarity plug
Be sure to always use the supplied AC power adaptor. Even AC
power adaptors having the same voltage and plug polarity can
damage this product due to the current capacity or other
factors.
2 Place the headphones on the transmitter so that
the headphones’ contact point meets the
transmitter’s contact pin, and make sure that the
CHG indicator lights up.
It takes approximate 3.5 hours to fully charge the battery
(the CHG indicator goes off when charging is complete).
When the transmitter’s contact pin meets the
headphones’ contact point, the CHG indicator on the
top of the left housing lights up in red.
Confirm that the headphones make a "click" sound
when you put then on the transmitter.
When the headphones are correctly placed on the
transmitter, the upper surface of the headphones
becomes level with the transmitter.
Charging and usage time
Approx. charging time Approx. usage time*
1
3.5 hours*
2
25 hours*
3
*
1
at 1 kHz, 0.1 mW + 0.1 mW output
*
2
hours required to fully charge an empty battery
*
3
Time may vary, depending on the temperature or conditions of
use.
If the CHG indicator is not lit
The indicator will not light up if the headphones’ contact
point does not meet the transmitters contact pin. In this
case, remove the headphones and insert them in the
transmitter again so that the indicator lights up.
To recharge the headphone battery after use
Place the headphones on the transmitter after use. The CHG
indicator lights up, and then charging starts.
When charging is complete, there is no need to remove the
headphones from the transmitter after charging has
completed.
Notes
The transmitter automatically turns off while charging the battery.
Avoid exposure to temperature extremes, direct sunlight, moisture,
sand, dust or mechanical shock.
If the headphones are used outside the recommended temperature
range, the CHG indicator flashes and charging stops. Charge in an
environmental temperature of between 5°C and 35°C.
If you haven’t used the headphones for a long period of time, the
life of the rechargeable battery may become short. This will
improve when you repeat the charging and discharging process
several times.
When the battery life reduces to half, this may be the end of battery
lifetime. For how to change batteries, consult your place of purchase
or a Sony dealer.
Do not store the headphones in hot places for a long period of time.
When storing it for more than a year, charge the battery once a year
to prevent over discharge.
Do not touch the contact pin of the transmitter. If a contact pin
becomes dirty, charging may not be possible.
Charging may not be completed if the transmitters contact pin and
headphones’ contact point are dusty. Wipe them with a cotton bud,
etc.
The sound cuts off
The transmitter stops transmitting if no signal is input for 5
minutes.
If you connect the transmitter to an AV component using the
headphone jack, raise the volume level on the connected AV
component within the range where the sound is not distorted.
The battery cannot be charged
Check if the CHG indicator turns on. If not, put the headphones
on the transmitter correctly so that the CHG indicator turns on.
The transmitter’s contact pin and headphones’ contact point are
dusty.
Wipe them with a cotton bud, etc.
You are attempting to charge the battery in an environment
outside the recommended temperature range of between 5°C and
35°C. You cannot charge while the CHG indicator flashes.
Charge in an environmental temperature of between 5°C and
35°C.
Check that the AC power adaptor is connected to the transmitter.

Precautions

If the transmitter is not to be used for a long period of
time, disconnect the AC power adaptor from the AC
outlet by holding the plug. Do not pull on the cord.
Do not leave the wireless stereo headphone system in a
location subject to direct sunlight, heat or moisture.
Notes on headphonesTo reduce the risk of hearing damage
Avoid using headphones at high volume. Hearing experts
advise against continuous, loud and extended play. If you
experience a ringing in your ears, reduce the volume or
discontinue use.
Caring for others
Keep the volume at a moderate level. This will allow you to
hear outside sounds and to be considerate to the people
around you.
If you have any questions or problems concerning the
system that are not covered in this manual, please consult
your nearest Sony dealer.
Be sure to bring the headphones and the transmitter to the
Sony dealer when requiring repair work.

Specifications

RF stereo transmitter (TMR-RF865R)
Modulation
FM stereo
Carrier frequency
863.52 MHz, 864.02 MHz, 864.52 MHz
Channel
Ch1, Ch2, Ch3
Transmission distance
Approx. 100 m of longest
Audio inputs
Pin jacks (left/right)
Stereo mini jack
Power requirements
DC 12 V (from the supplied AC power adaptor)
Dimensions
Approx. 120 mm × 264 mm × 120 mm (w/h/d)
Mass
Approx. 470 g
Rated power consumption
3.0 W
Operating temperature
5°C to 35°C (41°F to 95°F)
Wireless stereo headphones (MDR-RF865R)
Playback frequency range
10 Hz – 22,000 Hz
Power source
Built-in lithium-ion rechargeable battery
Mass
Approx. 320 g
Operating temperature
5°C to 35°C (41°F to 95°F)
Supplied accessories
AC power adaptor (12 V) (1)
Connecting cable
(stereo mini plug pin plug × 2), 1 m (1)
Card warranty (1)
Operating Instructions (this manual) (1)
Design and specifications are subject to change without
notice.
* “WALKMAN” and “WALKMAN” logo are registered trademarks
of Sony Corporation.
MDR-RF865RK

© 2011 Sony Corporation Printed in China

Wireless Stereo

Headphone

System

4-264-130-13(1)

Operating Instructions

Mode d’emploi

Mode d'emploi

Consultez gratuitement le manuel de la marque Sony MDR-RF865RK ici. Ce manuel appartient à la catégorie Écouteurs et a été évalué par 1 personnes avec une moyenne de 7.4. Ce manuel est disponible dans les langues suivantes: Français, Anglais. Vous avez une question sur le MDR-RF865RK de la marque Sony ou avez-vous besoin d’aide? Posez votre question ici

Besoin d’aide?

Vous avez une question sur le Sony MDR-RF865RK et la réponse n'est pas dans le manuel? Posez votre question ici. Fournissez une description claire et complète du problème, et de votre question. Plus votre problème et votre question sont clairement énoncés, plus les autres propriétaires de Sony MDR-RF865RK ont de chances de vous fournir une bonne réponse.

Nombre de questions : 0

Spécifications du MDR-RF865RK de la marque Sony

Vous trouverez ci-dessous les spécifications du produit et les spécifications du manuel du Sony MDR-RF865RK.

Généralités
Marque Sony
Modèle MDR-RF865RK | MDR-RF865RK
Produit écouteur
EAN 4905524700206, 3465813095365, 4905524700213
Langue Français, Anglais
Type de fichier Mode d’emploi (PDF)
Batterie
Autonomie maximum de la batterie 25 h
Casques/Ecouteurs
Impédance 40 Ohm
Unité de lecture 40 mm
Type d'aimant Néodyme
Système acoustique Fermé
Type de pilote Dynamique
Suppression du bruit Oui
Fréquence des écouteurs 10 - 22000 Hz
Contenu de l'emballage
Guide de démarrage rapide Oui
Connectivité
Portée du routeur sans fil 100 m
Technologie de connectivité Sans fil
Poids et dimensions
Poids 320 g
représentation / réalisation
Couleur du produit Noir
Style de casque portable Arceau
Type de produit Écouteurs
Utilisation recommandée Musique
Microphone
Type de microphone Indisponible
voir plus

Foire aux questions

Vous ne trouvez pas la réponse à votre question dans le manuel? Vous trouverez peut-être la réponse à votre question dans la FAQ sur le Sony MDR-RF865RK au dessous de.

Votre question n'est pas dans la liste ? Posez votre question ici

Aucun résultat