Sony MDR-RF895RK mode d'emploi

Sony MDR-RF895RK
8.9 · 4
PDF mode d'emploi
 · 2 pages
Français
mode d'emploiSony MDR-RF895RK

Wireless Stereo

Headphone System

©2017 Sony Corporation Printed in Vietnam4-691-894-12(1)MDR-RF895RK
Operating Instructions
Mode d’emploi

How to use

Tips for charging
Charge supplied battery first
The supplied rechargeable nickel-metal hydride battery is
not charged from the first time you use it. Be sure to
charge them before use.
About auto charge function
Placing the headphones on the transmitter automatically
turns them off, then charging starts. This eliminates the
need for turning on/off every time you wear and take off
the headphones.
If CHARGE/RED indicator does not light up red
Check if the right and left headphones are rested on the
transmitter correctly. Take off the headphones and place
them on the transmitter again so that the headphones’
contact points meet the transmitter’s contact pins.
Charging may not be completed if the transmitter’s
contact pin and headphones’ contact point are dusty.
Wipe them with a cotton bud, etc.
Charging and usage time
Approx. charging time Maximum usage time
1)
7 hours
2)
20 hours
3)
1) at 1 kHz, 0.1 mW + 0.1 mW output
2) hours required to fully charge an empty battery
3) Time may vary, depending on the temperature or
conditions of use.
To recharge supplied battery after
use
Place the headphones on the transmitter after use. The
CHARGE/RED indicator lights up red, then charging starts.
When charging is complete, there is no need to remove
the headphones from the transmitter.
Remaining battery
To check the remaining battery charge of the headphones,
turn on the POWER switch and check the POWER indicator.
The battery is still serviceable when the indicator lights up
green.
Charge the headphones if the POWER indicator turns off,
dims, flashes, or the sound becomes distorted or noisy.
Notes
Insert the AC adaptor plug firmly.
Be sure to use the supplied AC adaptor. Using AC
adaptors with different plug polarity or other
characteristics can cause product failure.
Unified
polarity plug
The battery capacity may decrease if the headphones
are turned on and placed on the transmitter with the AC
adaptor disconnected.
The transmitter automatically turns off while charging
the headphones.
This system is designed to charge only the supplied
rechargeable battery BP-HP800-11 for safety. Note that
other types of rechargeable battery cannot be charged
with this system.
If dry batteries are installed, they cannot be charged.
Do not attempt to use the supplied rechargeable battery
BP-HP800-11 for other components. It is for use with this
system only.
Charge in an environmental temperature of between
5 °C and 35 °C.
When the battery life reduces to half, this may be the
end of battery lifetime. The supplied rechargeable
battery BP-HP800-11 is not commercially available. You
can order the battery from the store where you
purchased this system, or at your nearest Sony dealer.
Do not touch the contact pins of the transmitter. If the
contact pins become dirty, charging may not be
possible.
Charging may not be completed if the transmitter’s
contact pins and headphones’ contact points are dusty.
Wipe them with a cotton bud, etc.
Using the headphones
with separately-sold dry
batteries
Commercially available (LR03 (size AAA)) dry batteries can
also be used to power the headphones. Install two
batteries in the same manner as described in step 1 of
“How to use.
If you attempt to charge the headphones with dry
batteries installed, the CHARGE/RED indicator lights up
red for 15 seconds, then turns off. The battery charge
function is not activated.
Battery life
Battery Approx. usage time
1)
Sony alkaline battery LR03
(size AAA)
24 hours
2)
1) at 1 kHz, 0.1 mW + 0.1 mW output
2) Time may vary, depending on the temperature or
conditions of use.
Note
Do not carry a dry battery together with coins or other
metallic objects. It can generate heat if the positive and
negative terminals of the battery are accidentally come
into contact with metallic objects.
Tips for connection
When you connect the stereo mini cable (stereo mini
jack) directly to an earphone jack (monaural mini jack),
the audio signal may not be output through the right
channel.
Tips for volume setting
If you connect the transmitter to the headphone jack of
the A/V component, set the volume of the A/V
component as high as possible but not so high that the
audio signal becomes distorted.
When watching videos, be careful not to raise the
volume too high in quiet scenes. You may hurt your ears
when a loud scene is played.
Tips for sound effect
Slide the switch to select the desired sound effect, OFF or
VOICE.
Position of
switch
Sound effect and suitable sound
source
OFF
Normal playback of the
headphones.
VOICE
Produces a clearer announcer’s
voice.
Notes
The volume of the headphones may vary, depending on
the input signal and the setting of the EFFECT switch.
The sound effect may not be obtained depending on
the input sound sources.
Tips for better reception
Receiving performance
This system utilizes very high frequency signals in the 800
MHz band so the receiving performance may deteriorate
due to the surroundings. The following examples illustrate
conditions that may reduce the reception range or cause
interference.
Inside a building with walls containing steel beams
An area with many steel file cabinets, etc.
An area with many electrical appliances capable of
generating electromagnetic fields
The transmitter is placed on a metal instrument.
An area facing a roadway
Noise or interfering signals exist in the surroundings due
to radio transceivers in trucks, etc.
Noise or interfering signals exist in the surroundings
owing to wireless communication systems installed
along roadways.
Effective area of the transmitter
The optimum distance is up to approximately 100 m
without the system picking up some interference.
However, the distance may vary depending on the
surroundings and environment.
If the system picks up some noise within the above
mentioned distance, reduce the distance between the
transmitter and the headphones, or select another
channel.
When you use the headphones inside the effective area
of the transmitter, the transmitter can be placed in any
direction from the listener.
Even within the signal reception area, there are some
spots (dead spots) where the RF signal cannot be
received. This characteristic is inherent to RF signals, and
does not indicate malfunction. By slightly moving the
transmitter, location of the dead spot can be changed.
Replacing the earpads
The earpads are replaceable. If the earpads become dirty
or worn out, replace them as illustrated below. The
earpads are not commercially available. You can order
replacements from the store where you purchased this
system, or at your nearest Sony dealer.
1 Remove the old earpad by pulling it out of the groove
on the housing.
2 Fit the new earpad in the groove of the housing.
Make sure the earpad is set to the vertical position.
Precautions
When this system is not to be used for a long period of
time, disconnect the AC adaptor from the AC outlet
holding the plug, and remove the battery from the
headphones to avoid damage caused by battery
leakage and subsequent corrosion.
Do not leave this system in a location subject to direct
sunlight, heat or moisture.
You may hear some noise when you disconnect the AC
adaptor from the transmitter before taking off the
headphones.
Avoid exposure to temperature extremes, direct sunlight,
moisture, sand, dust or mechanical shock.
Please note that water does not splash, this product is
not waterproof specification.
Notes on headphonesTo reduce the risk of hearing damage
Avoid using headphones at high volume. Hearing experts
advise against continuous, loud and extended play. If you
experience a ringing in your ears, lower the volume or
discontinue use.
Caring for others
Keep the volume at a moderate level. This will allow you
to hear outside sounds and to be considerate to the
people around you.
If you have any questions or problems concerning the
system that are not covered in this manual, please consult
your nearest Sony dealer.
Be sure to bring the headphones and the transmitter to
the Sony dealer when requiring repair work.
Troubleshooting
If you run into any problems using this system, use the
following checklist. Should any problem persist, consult
your nearest Sony dealer.
No sound/Low sound
Check the connection of the A/V component or the AC
adaptor.
Check that the A/V component is turned on.
If you connect the transmitter to an A/V component
using the headphone jack, raise the volume level on the
connected A/V component within the range where the
sound is not distorted.
Change the radio frequency with the CHANNEL selector
on the transmitter, then change the radio frequency to
that of the transmitter with the AUTO TUNING button on
the headphones.
Use the headphones near the transmitter, or change the
position of the transmitter.
Charge the supplied rechargeable battery, or replace dry
batteries with new ones. If the POWER indicator is still
off after charging, take the headphones to a Sony dealer.
Raise the headphone volume.
The sound cuts off
The transmitter turns off if no signal or low signal is
input for 4 minutes. If you connect the transmitter to an
A/V component using the headphone jack, raise the
volume level on the connected A/V component within
the range where the sound is not distorted.
Distorted or intermittent sound (sometimes with noise)
Use the headphones near the transmitter, or change the
position of the transmitter.
Do not place the transmitter on a metallic table.
If you connect the transmitter to an A/V component
using the headphone jack, lower the volume level on the
connected A/V component within the range where the
sound is not distorted.
Change the radio frequency with the CHANNEL selector
on the transmitter, then change the radio frequency to
that of the transmitter with the AUTO TUNING button on
the headphones.
Charge the supplied rechargeable battery, or replace dry
batteries with new ones. If the POWER indicator is still
off after charging, take the headphones to a Sony dealer.
Loud background noise
If you connect the transmitter to an A/V component
using the headphone jack, raise the volume level on the
connected A/V component within the range where the
sound is not distorted.
Charge the supplied rechargeable battery, or replace dry
batteries with new ones. If the POWER indicator is still
off after charging, take the headphones to a Sony dealer.
Do not place the transmitter on a metallic table.
Use the headphones near the transmitter.
The POWER/GREEN indicator flashes green
No signal or low signal is input. Start playback of the A/V
component, or raise the volume of the connected A/V
component within the range where the sound is not
distorted, otherwise the transmitter will turn off. If no
signal or low signal is input for about 4 minutes, the
transmitter turns off automatically.
Battery cannot be charged/ CHARGE/RED indicator flashes red, or does not light up red
Check that the right/left of the headphones and
transmitter correspond, and put the headphones on the
transmitter correctly.
Install the supplied rechargeable nickel-metal hydride
battery. Dry batteries and rechargeable batteries other
than the supplied cannot be charged.
If the CHARGE/RED indicator does not light up red even
though you put the headphones on the transmitter and
wait for a while, it may be the end of battery lifetime.
You can order the supplied rechargeable battery
BP-HP800-11 from the store where you purchased this
system, or at your nearest Sony dealer.
Charging may not be completed if the transmitter’s
contact pin and headphones’ contact point are dusty.
Wipe them with a cotton bud, etc.
Short usage time (the supplied rechargeable battery)
Clean the + and − terminal of the supplied rechargeable
battery and the charging terminal of transmitter/
headphone with a dry cloth.
Recharge the supplied rechargeable battery after the
fully discharged.
Specifications
RF stereo transmitter (TMR-RF895R)
Modulation FM stereo
Operating frequency
863.0 MHz – 865.0 MHz
Maximum output power
< 10 mW
Channel Ch1, Ch2, Ch3
Transmission distance
Approx. 100 m of longest
Audio inputs Stereo mini jack
Power requirements
DC 12 V (from the supplied AC adaptor)
Dimensions Approx. 130 mm × 273 mm × 160 mm
(w/h/d)
Mass Approx. 265 g
Rated power consumption
2.0 W
Operating temperature
5°C to 35°C
Wireless stereo headphones (MDR-RF895R)
Frequency response
10 Hz – 22,000 Hz
Power source Supplied rechargeable nickel-metal
hydride battery BP-HP800-11, or
commercially available (LR03 (size AAA))
dry batteries
Mass Approx. 275 g
Operating temperature
5°C to 35°C
Included items
RF stereo transmitter TMR-RF895R
Wireless stereo headphones MDR-RF895R
AC adaptor (12 V) (1)
Rechargeable nickel-metal hydride battery
BP-HP800-11 (1)
Stereo mini cable (stereo mini plug), 1.5 m (1)
Card warranty (1)
Operating Instructions (this manual) (1)
Design and specifications are subject to change without
notice.
Svenska
Härmed försäkrar Sony Corporation att denna utrustning
överensstämmer med direktiv 2014/53/EU.
Den fullständiga texten till EU-försäkran om
överensstämmelse finns på följande webbadress:
http://www.compliance.sony.de/
Dansk
Herved erklærer Sony Corporation, at dette udstyr er i
overensstemmelse med direktiv 2014/53 / EU.
Den fulde ordlyd af EU-overensstemmelseserklæringen er
tilgængelig på følgende internetadresse:
http://www.compliance.sony.de/
Suomi
Sony Corporation vakuuttaa, että tämä laite on direktiivin
2014/53/EU mukainen.
EU-vaatimustenmukaisuusvakuutuksen täysimittainen
teksti on saatavilla seuraavassa internetosoitteessa:
http://www.compliance.sony.de/
Norsk
Herved erklærer Sony Corporation at utstyrstypen er i
samsvar med direktiv 2014/53/EU.
EU-erklæring fulltekst finner du på Internett under:
http://www.compliance.sony.de/
Français
Le soussigné, Sony Corporation, déclare que cet
équipement est conforme à la Directive 2014/53/UE.
Le texte complet de la déclaration UE de conformité est
disponible à l’adresse internet suivante :
http://www.compliance.sony.de/
Deutsch
Hiermit erklärt Sony Corporation, dass diese Funkanlage
der Richtlinie 2014/53/EU entspricht.
Der vollständige Text der EU-Konformitätserklärung ist
unter der folgenden Internetadresse verfügbar:
http://www.compliance.sony.de/
Español
Por la presente, Sony Corporation declara que este equipo
es conforme con la Directiva 2014/53/UE.
El texto completo de la declaración UE de conformidad
está disponible en la dirección Internet siguiente:
http://www.compliance.sony.de/
Nederlands
Hierbij verklaart Sony Corporation dat deze
radioapparatuur conform is met Richtlijn 2014/53/EU.
De volledige tekst van de EU-conformiteitsverklaring kan
worden geraadpleegd op het volgende internetadres:
http://www.compliance.sony.de/
Italiano
Con la presente, Sony Corporation dichiara che questo
apparecchio è conforme alla Direttiva 2014/53/UE.
Il testo completo della dichiarazione di conformità UE è
disponibile al seguente indirizzo Internet:
http://www.compliance.sony.de/
Português
O(a) abaixo assinado(a) Sony Corporation declara que o
presente equipamento está em conformidade com a
Diretiva 2014/53/UE.
O texto integral da declaração de conformidade está
disponível no seguinte endereço de Internet:
http://www.compliance.sony.de/
Slovensky
Sony Corporation týmto vyhlasuje, že zariadenie je v
súlade so smernicou 2014/53/EÚ.
Úplné vyhlásenie EÚ o zhode je k dispozícii na tejto
internetovej adrese:
http://www.compliance.sony.de/
Slovenščina
Sony Corporation potrjuje, da je ta oprema skladna z
Direktivo 2014/53/EU.
Celotno besedilo izjave EU o skladnosti je na voljo na
naslednjem spletnem naslovu:
http://www.compliance.sony.de/
Česky
Sony Corporation tímto prohlašuje, že toto zařízení je v
souladu se směrnicí 2014/53/EU.
Úplné znění EU prohlášení o shodě je k dispozici na této
internetové adrese:
http://www.compliance.sony.de/
Magyar
A Sony Corporation igazolja, hogy ez a készülék megfelel a
2014/53/EU irányelvnek.
Az EU-megfelelőségi nyilatkozat teljes szövege elérhető a
következő internetes címen:
http://www.compliance.sony.de/
Български
С настоящото, Sony Corporation декларира, че това
оборудване е в съответствие с Директива 2014/53/EU.
Цялостният текст на ЕС декларацията за съответствие
може да се намери на следния интернет адрес:
http://www.compliance.sony.de/
Polski
Sony Corporation niniejszym oświadcza, że to urządzenie
jest zgodne z dyrektywą 2014/53/UE.
Pełny tekst deklaracji zgodności UE jest dostępny pod
następującym adresem internetowym:
http://www.compliance.sony.de/
Română
Prin prezenta, Sony Corporation declară că acest
echipament este în conformitate cu Directiva 2014/53/UE.
Textul integral al declarației UE de conformitate este
disponibil la următoarea adresă internet:
http://www.compliance.sony.de/
Ελληνικά
Με την παρούσα Sony Corporation δηλώνει ότι, αυτή η
συσκευή πληροί τους όρους της οδηγίας 2014/53/EU.
Το πλήρες κείμενο της δήλωσης συμμόρφωσης ΕΕ
διατίθεται στην ακόλουθη ιστοσελίδα στο διαδίκτυο:
http://www.compliance.sony.de/
Connect the AC adaptor. Charge the headphones.
To AC
outlet
Connect the A/V component, following hookup or below. Using the headphone jack of the A/V component
Stereo mini plug
Headphone jack
(Stereo mini jack)
TV, Digital music player, etc.
L (white)
R (red)
Stereo mini plug
Audio out
(L/R) jacks
Stereo system, Blu-ray Disc player, DVD player, TV*, etc.
* In case of no headphone jack.
If you cannot receive a clear audio signal
First change the radio frequency with the CHANNEL selector switch on the
transmitter, then briefly press the AUTO TUNING button on the headphones.
Noise Reduction process
The transmitter compresses the audio signal and converts it to RF signal. The headphones convert the received RF
signal to an audio signal and decompresses it. This process reduces noise picked up during transmission.
input signal
output signal
decompression
compression
dynamic range
Transmitter unit Headphones unit
RF transmission
noise level (low)
1
2 34
5
The transmitter compresses the audio signals dynamic range, then converts it to RF signal.
Noise may occur due to long distance transmission, etc.
The headphones convert the RF signal to an audio signal.
Noise may occur during conversion.
Decompression of the audio signals dynamic range reduces the noise level and improves the S/N (signal-to-noise)
ratio.
Adjust the volume.Start playback of the A/V component.Wear the headphones.Before listening
To reduce the risk of hearing damage, first lower the volume.
Tactile dot
Up Down
Tactile dot
Using the audio out (L/R) jacks of the A/V component
Use a connection cable (not supplied) between the transmitter and the A/V component.
If the sound is distorted by connecting the transmitter to the A/V component’s audio out (L/R) jacks, reconnect the transmitter to the headphone jack.
If the transmitter detects no signal or no sound, check the connection of the connected A/V components, then check the audio setting of the connected A/V components.
Insert the supplied rechargeable battery BP-HP800-11 into the left housing of the headphones.
Observe the correct polarity when installing battery.
Rechargeable nickel-metal hydride
battery BP-HP800-11 (supplied)
Insert the
end first.
(Green)
English Wireless Stereo Headphone System
WARNING
To reduce the risk of fire or electric shock, do not
expose this apparatus to rain or moisture.
To reduce the risk of fire or electric shock, do not expose
this apparatus to dripping or splashing, and do not place
objects filled with liquids, such as vases, on the apparatus.
Do not expose the batteries (battery pack or batteries
installed) to excessive heat such as sunshine, fire or the
like for a long time.
To avoid electrical shock, do not open the cabinet. Refer
servicing to qualified personnel only.
Do not install the appliance in a confined space, such as a
bookcase or built-in cabinet.
The AC Adaptor is not disconnected from the mains as
long as it is connected to the AC outlet, even if the unit
itself has been turned off.
As the main plug of AC power adaptor is used to
disconnect the AC power adaptor from the mains, connect
it to an easily accessible AC outlet. Should you notice an
abnormality in it, disconnect it from the AC outlet
immediately.
Excessive sound pressure from earphones and
headphones can cause hearing loss.
The nameplate of transmitter is located on the bottom
exterior.
The nameplate of the headphones is located on the back
side of the slider.
The validity of the CE marking is restricted to only those
countries where it is legally enforced, mainly in the
countries EEA (European Economic Area).
Hereby, Sony Corporation declares that this equipment is
in compliance with Directive 2014/53/EU.
The full text of the EU declaration of conformity is
available at the following internet address:
http://www.compliance.sony.de/
Disposal of waste batteries and electrical and electronic equipment (applicable in the European Union and other European countries with separate collection systems)
This symbol on the product, the battery or on the packaging
indicates that the product and the battery shall not be treated as
household waste. On certain batteries this symbol might be used in
combination with a chemical symbol. The chemical symbols for
mercury (Hg) or lead (Pb) are added if the battery contains more
than 0.0005% mercury or 0.004% lead. By ensuring these products
and batteries are disposed of correctly, you will help prevent
potentially negative consequences for the environment and human
health which could otherwise be caused by inappropriate waste
handling. The recycling of the materials will help to conserve natural
resources.
In case of products that for safety, performance or data integrity
reasons require a permanent connection with an incorporated
battery, this battery should be replaced by qualified service staff
only. To ensure that the battery and the electrical and electronic
equipment will be treated properly, hand over these products at
end-of-life to the applicable collection point for the recycling of
electrical and electronic equipment. For all other batteries, please
view the section on how to remove the battery from the product
safely. Hand the battery over to the applicable collection point for
the recycling of waste batteries. For more detailed information
about recycling of this product or battery, please contact your local
Civic Office, your household waste disposal service or the shop
where you purchased the product or battery.
Notice for customers: the following information is only
applicable to equipment sold in countries applying EU
directives
This product has been manufactured by or on behalf of
Sony Corporation, 1-7-1 Konan Minato-ku Tokyo, 108-0075
Japan. Inquiries related to product compliance based on
European Union legislation shall be addressed to the
authorized representative, Sony Belgium, bijkantoor van
Sony Europe Limited, Da Vincilaan 7-D1, 1935 Zaventem,
Belgium. For any service or guarantee matters, please
refer to the addresses provided in the separate service or
guarantee documents.
Checking the included
items
RF stereo transmitter
TMR-RF895R (1)
AC adaptor (1)
Wireless stereo
headphones MDR-RF895R
(1)
Stereo mini cable (stereo
mini plug), 1.5 m (1)
Rechargeable nickel-metal
hydride battery BP-
HP800-11 (1)
Features
Thank you for purchasing the Sony MDR-RF895RK
Wireless Stereo Headphone System. Before operating the
unit, please read this manual thoroughly and retain it for
future reference.
Some features are:
Wireless system that allows you to listen to a
programme free the restriction of a cable
Up to 100 meters reception range*
High fidelity sound reproduction
New mode “VOICE” for clear hearing of personal voice
range
Noise reduction system to reproduce a clear sound with
minimum transmission noise
Comfortable fit
Smooth and Comfortable Earpads
Long playback time (maximum 20 hours)
Easy recharging function with secure charging
mechanism
Rechargeable Battery
Automatic tuning on headphones for optimum signal
reception
3 transmission channels available
Volume control function and sound effect function on
the headphones
* Transmission distance varies depending on conditions of
use
(Red)
(Off)
Complete when indicator
turns off.
Check the CHARGE/
RED indicator lights
up red.
4
2
3
After use
Turn off the power of the headphones.
About sending RF signals
The transmitter starts sending RF signals automatically
when it detects an audio signal from the connected
component. Note that;
Noise may occur depending on the transmitter position
and room conditions. It is recommended to place the
transmitter in a location that produces the clearest
sound.
If the transmitter is placed on a metallic table, you may
hear noise, or the reception range may decrease. Do
not place on a metallic table.
If no signal or low signal is input for about 4 minutes
When no signal is input for about 4 minutes, the
transmitter turns off automatically*. The POWER indicator
of the transmitter blinks for 4 minutes, then turns off. The
transmitter restarts after receiving an audio signal again.
The transmitter may also turn off if low signal is input for
about 4 minutes. In this case, raise the volume of the
connected A/V component within the range where the
sound is not distorted, then lower the volume of the
headphones.
* If signal noise is output from the connected A/V
component, the transmitter may not turn off, even
when no audio signal is input.
7

5 6

1

Mode d'emploi

Consultez gratuitement le manuel de la marque Sony MDR-RF895RK ici. Ce manuel appartient à la catégorie Écouteurs et a été évalué par 4 personnes avec une moyenne de 8.9. Ce manuel est disponible dans les langues suivantes: Français, Anglais. Vous avez une question sur le MDR-RF895RK de la marque Sony ou avez-vous besoin d’aide? Posez votre question ici

Besoin d’aide?

Vous avez une question sur le Sony MDR-RF895RK et la réponse n'est pas dans le manuel? Posez votre question ici. Fournissez une description claire et complète du problème, et de votre question. Plus votre problème et votre question sont clairement énoncés, plus les autres propriétaires de Sony MDR-RF895RK ont de chances de vous fournir une bonne réponse.

ALAIN JUVENT • 8-11-2020 1 commentaire

Depuis hier, dernière utilisation de mon casque sans fil Sony MDR-RF895 RK, le voyant rouge du transmetteur ne s'allume plus (ni ver d’ailleurs) alors que le casque y est correctement posé et qu'il est branché sur secteur. Quelle est la solution ? Merci

Depuis hier, dernière utilisation de mon casque sans fil Sony MDR-RF895 RK, le voyant rouge du transmetteur ne s'allume plus ...
Voir la photo.
Zottola • 2-5-2021

Depuis hier, dernière utilisation, alors que l'appareil (casque SONY sans fil MDR RF895 RK )est toujours branché sur le secteur et le casque posé correctement, le voyant rouge du transmetteur stéréo (soit la base ) et indiquant la charge ne s'allume plus. Le voyant vert du casque s'allumait encore mais plus aucune transmission. Que dois-je faire ? Meci

Répondez à cette question
ALAIN JUVENT • 8-11-2020 1 commentaire

Depuis hier, dernière utilisation, alors que l'appareil (casque SONY sans fil MDR RF895 RK )est toujours branché sur le secteur et le casque posé correctement, le voyant rouge du transmetteur stéréo (soit la base ) et indiquant la charge ne s'allume plus. Le voyant vert du casque s'allumait encore mais plus aucune transmission. Que dois-je faire ? Meci

Depuis hier, dernière utilisation, alors que l'appareil (casque SONY sans fil MDR RF895 RK )est toujours branché sur le secte...
Voir la photo.
Chris • 4-10-2022

même PB chez moi a priori adaptateur secteur/12V DC HS

Répondez à cette question
Moutard • 28-12-2020 Pas de commentaire

Bonjour j ai un casque Sony MDR RF 895RK. La base estbranchée sur le secteur depuis un moment le voyant rouge est fixe que dois je faire

Répondez à cette question
PRAT • 29-1-2021 Pas de commentaire

Le casque est en charge pour la première fois charge depuis 10 Heures et le voyant est toujours au rouge pourquoi?

Répondez à cette question
Clemence • 11-12-2020 Pas de commentaire

Bonjour, j'ai acheté le casque Sony MDR-RF895RK, il est en charge depuis 10h et le voyant resté toujours rouge. Faut-il retirer le film plastique qui entouré les 2 piles rechargeables ? J'arrive à entendre des voix mais la qualité est mauvaise et ne correspondent pas à ce que je regarde. Merci pour votre aide

Répondez à cette question
GASTARD Jean-Yves • 26-10-2021 Pas de commentaire

Les piles HFE NImh rechargeable 750 mAh AAA 1,2 v sont-elles compatibles avec le casque MDR-FR895RK

Répondez à cette question
gerard PRADAL • 7-2-2021 Pas de commentaire

A QUOI SERT LE BOUTON TACTIL sur ecouteur gauche ? Que signifie en clair : Lancez la lecture de l'appareil ? Impossible d'entendre ? Connection appareil B. Merci de votre aide.

Répondez à cette question
Bigot • 2-10-2020 Pas de commentaire

Mon casque reste encharge

Répondez à cette question
batude • 13-6-2020 Pas de commentaire

comment recharger une pile ou bien faut il en acheter une autre?

Répondez à cette question
thalmann ruth • 4-5-2022 Pas de commentaire

Sony MDR-RF895RK mode d'emploi... Comment fait on pour charger les Batteries du casque

Répondez à cette question

Nombre de questions : 27

Spécifications du MDR-RF895RK de la marque Sony

Vous trouverez ci-dessous les spécifications du produit et les spécifications du manuel du Sony MDR-RF895RK.

Généralités
Marque Sony
Modèle MDR-RF895RK
Produit écouteur
Langue Français, Anglais
Type de fichier Mode d’emploi (PDF)

Foire aux questions

Vous ne trouvez pas la réponse à votre question dans le manuel? Vous trouverez peut-être la réponse à votre question dans la FAQ sur le Sony MDR-RF895RK au dessous de.

Votre question n'est pas dans la liste ? Posez votre question ici

Aucun résultat