Xit XTCGT3i mode d'emploi

Xit XTCGT3i
9.1 · 1
PDF mode d'emploi
 · 1 page
Anglais
mode d'emploiXit XTCGT3i

lNSTRUCTIONS

The XTCGT3i is a battery grip that can hold two Battery Pack
LP-E8 or six size-AA batteries. It is also equipped with a
vertical-grip shutter button, Main Dial, etc. to enable shooting
in the same way as with horizontal grip.

ATTACHING TO THE CAMERA

SPECIFICATIONS

INSTALLING THE BATTERY PACKS

INSERTING SIZE-AA BATTERIES

Protective cover
Electrical contacts
Attachment screw
Guide pin
Attach/detach knob
Battery magazine release handle
DC cord mount
Aperture/exposure compensation button
AF point selection/Magnify button
AE lock/FE lock/Index/Reduce button
Vertical-grip operation switch
Shutter button
Camera battery compartment cover slot
Main Dial
Hand strap mount
Tripod socket
Battery magazine protective cover
Battery magazine
Battery pack compartment
Battery magazine (For size-AA batteries)
1. Remove the battery from the camera. (Fig. 1)
2. Pull out the cameras battery compartment cover at a slanted
angle to detach. (Fig. 2)
Perform the operation over a table so as not to drop the
camera
3. lnsert the detached cover into its storage slot to ensure that it
will not be lost. (Fig. 3)
4. Remove the protective cover, and then insert the electrical
contacts into the camera battery compartment. (Fig. 4-1)
5. Align the attachment screw with the camera's tripod socket,
and then turn the attach/detach knob to tighten securely.
(Fig. 4-2)
Do not further push open the battery compartment
cover when it is already open. Doing so may damage
its hinge.
Be sure to attach the battery grip to the camera before
inserting the batteries. The results of the battery check
may not be displayed properly if you attach the battery
grip to the camera with the batteries already inside.
Before removing the battery grip from the camera, be
sure to turn the camera's power switch to <OFF>, and
take out the batteries. After removing the batteries, attach
the protective cover to the electrical contacts.
1. After ipping out the release handle, turn it as shown by the
arrow, and then pull out the battery magazine (for size-AA
batteries). (Flg. 5)
2. Insert one or two Battery Pack LP-E8 into the battery
magazine for LP-E8 . (Fig. 6)
3. Remove the protective cover of the battery magazine, and
then attach it into the battery grip. (Flg. 7-1)
After attaching, check that the battery magazine is securely
attached to the battery grip.
4. Close the release handle. (Fig. 7-2)
If only one battery pack is used, it may be inserted in
either the right or left side.
If two battery packs are inserted, power is supplied
simultaneously by both battery packs. Two battery packs
with dierent charging levels can be inserted and used
without any problems.
Remove the battery packs or size-AA batteries from
the battery grip when the camera will not be used for
an extended period.
1. Insert the batteries into the battery magazine
(for size-AA batteries) (Fig.8) Make sure the + and - battery
contacts are properly oriented as shown in the illustration.
2. Attach the battery magazine into the battery grip. (Fig. 9-1)
After attaching, check that the battery magazine is securely
attached to the battery grip.
3. Close the release handle. (Fig. 9-2)
Fewer images can be shot when using size-AA batteries
Also, the number of possible shots may vary depending
on the batteries brand and storage conditions, so usage
of size-AA batteries is recommended only for emergencies.
With size-AA batteries, use six new batteries of the same
brand at temperatures above 20°C/68°F. The camera may
not function when used in low temperatures or when old
and new batteries are used together.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20

PARTS NAME

USING THE BATTERY GRIP

Turning the vertical-grip operation switch to <ON> (Fig. 11)
makes the battery grip buttons and dial function in the same
way as those on the camera.
When shooting in the horizontal-grip position, turn the vertical-
grip operation switch to <OFF> so that you do not accidentally
use the buttons or dial on the battery grip.
Hand Strap (sold separately) can be used for enabling a
more secure grip.
The battery level can be checked on the camera.
Battery: (1) One or two Battery Packs LP-E8
(2) Six Size-AA Alkaline batteries
(3)AC Adapter Kit
Power switch: Cameras power switch
Possible shots: Refer to your camera's Instruction Manual.
Working temperature range: 0°C - +4O°C / 32°F - 104°F
Working humidity: 85% or less
Dimensions: 131.8 (W) x 108 (H) x 79.9 (D) mm/
5.2 (W) x 4.3 (H) x 3.1 (D) in.
Weight: Approx. 230 g/8.1 oz.
(without batteries and
battery magazine)

USING A HOUSEHOLD POWER OUTLET

To connect to a household power outlet, use the AC Adapter Kit
(sold separately).
1. Connect the power cord to the AC adapter, and insert the
prongs into a power outlet. Connect the DC cord to the DC
coupler.
2. Insert the DC coupler into the release-handle-side battery pack
compartment of the battery magazine (for LP-E8), and then
attach to the battery grip. Pass the DC cord through the DC
cord groove. (Fig. 10)
Always set the cameras power switch to <OFF> before
disconnecting the power cord.
Be careful that the DC cord does not get pinched
between the battery grip and the battery magazine.
Canon
designed for

Item # XTCGT3i

Mode d'emploi

Consultez gratuitement le manuel de la marque Xit XTCGT3i ici. Ce manuel appartient à la catégorie Autres accessoires pour appareils photo et a été évalué par 1 personnes avec une moyenne de 9.1. Ce manuel est disponible dans les langues suivantes: Anglais. Vous avez une question sur le XTCGT3i de la marque Xit ou avez-vous besoin d’aide? Posez votre question ici

Besoin d’aide?

Vous avez une question sur le Xit XTCGT3i et la réponse n'est pas dans le manuel? Posez votre question ici. Fournissez une description claire et complète du problème, et de votre question. Plus votre problème et votre question sont clairement énoncés, plus les autres propriétaires de Xit XTCGT3i ont de chances de vous fournir une bonne réponse.

Nombre de questions : 0

Spécifications du XTCGT3i de la marque Xit

Vous trouverez ci-dessous les spécifications du produit et les spécifications du manuel du Xit XTCGT3i.

Généralités
Marque Xit
Modèle XTCGT3i
Produit Autres accessoires pour appareil photo
EAN 887575448853, 0887575448853
Langue Anglais
Type de fichier Mode d’emploi (PDF)
Caractéristiques
Compatibilité de marque Canon
Produits compatibles EOS Rebel T2i/T3i/T4i/T5i
Bouton marche/arrêt intégré Oui
Couleur du produit Noir
Type de produit Batterie grip pour appareil photo numérique
Contenu de l'emballage
Manuel d'utilisation Oui
Batterie
Taille de batterie cylindrique AA
Type de batterie LP-E8
Nombre de batteries prises en charge 8
voir plus

Foire aux questions

Vous ne trouvez pas la réponse à votre question dans le manuel? Vous trouverez peut-être la réponse à votre question dans la FAQ sur le Xit XTCGT3i au dessous de.

Votre question n'est pas dans la liste ? Posez votre question ici

Aucun résultat